Bedienungsanleitung Workzone IW36 (Seite 11 von 18) (Englisch)

724651

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018

20 21

Using the Trigger switch

This trigger switch (5) is an electronic variable

speed control which enables the user to vary

the speed continuously.

1. After selecting the direction of rotation using

the forward/reverse selector (2) and installing

the socket required for the work task at hand,

pressing on the trigger switch (5) will then

activate the impact wrench for use (Fig H).

2. The speed varies according to how far the trigger switch (5) is depressed.

The further it is depressed the faster the socket will rotate; the lighter it is

depressed, the slower it will rotate.

Fastening / Removing Screws, Nuts & Bolts

NOTE: When tightening a nut or a bolt always

start the fastener by hand by 2 or 3 threads

BEFORE using the impact wrench.

NOTE: The longer the impact wrench is operated

in the hammer function, the tighter the fastener

will become. 1 –2 seconds is normally sucient

with small nuts, and bolts even less time.

1. Select the appropriate forward or reverse

function using the selector (2).

2. Insert the socket onto the ½ “ square drive shaft (1).

3. Ensure your work piece (if applicable) is secured in position to stop it

moving whilst fastening or removing screws or bolts.

4. Hold the socket rmly against the bolt or screw to ensure it does not

slip (Fig I).

5. Slowly increase the pressure on the trigger switch (5) until you reach the

appropriate torque required for the fastening or removal of the screw or

bolt.

NOTE: Do not over tighten. Studs can break, threads stripped or threads

stretched where fasteners are over tightened.

NOTE: Always check the nut or bolt after tightening with the impact

wrench, the fastener is secure by a manual operation. i.e using a spanner or

wheel brace

IMPORTANT: If the impact wrench is used to secure and tighten wheel

nuts, ensure the nuts are manually checked with a hand brace after using

the brace.

Using the LED worklight

1. When the unit is switched (the trigger switch

(5) is depressed) , the LED work light (4) also

comes on to ensure better vision and to make

working in dark areas more safe (Fig I).

The working light goes out when the trigger

switch (5) is released.

CAUTION! LED is laser class 1!

Do not look directly into the laser as this may

result in damage to the eyes.

Operating tips

You will extend the life of your sockets/bits and do neater work if you

always put the socket/bits in contact with the work before pulling the

trigger switch (5). During the operation, hold the Impact Wrench rmly

and exert light, steady pressure. Too much pressure at low speed will stall

the Impact Wrench . Too little pressure will allow the driver socket/bit to

disengage from the fastener and damage the fastener head and driver bit.

Always use a good quality driver bit which matches the screw head

correctly. When using a at driver bit ensure a correct t between the

fastener and bit and it is recommended to use a bit with a sleeved guide.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone IW36 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info