724654
8
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
2400W Wet & Dry Vacuum
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: MWW706S-35L-1200WC • 06/2018 • 61406
(toll free)
AFTER SALES SUPPORT
(toll free)
2400W Wet & Dry Vacuum
e-mail: help@powertoolsupport.com1800 909 909
MODEL No.: MWW706S-35L-1200WC • 06/2018 • 61406
12 13
WARNING:
To prevent serious injury from accidental operation, turn the
power switch of the vacuum o and unplug the appliance from its
electrical outlet before performing any procedure in this section.
Before you connect the vacuum to a mains supply, make sure that
the data on the rating / technical label is identical to the mains data.
The Wet and Dry Vacuum should only be connected to a mains
power supply socket; an RCD (Residual Current Device) is
recommended.
The Wet and Dry Vacuum requires some assembly prior to use. This includes
assembly of the wheels, and dependent upon the use of the product, the
exible hose, tubes, lters, and accessories. The following detail covers the
assembly required for each function of the Wet and Dry Vacuum.
Assembly of the wheels
1. Remove the appliance head (2) from the tank (10) by unlocking the
2 x side locking handles (6) pulling them outwards, then upwards (Fig A).
Then turn the tank (10) upside down.
2. Fit the 4 x castor wheels (13) by inserting the mounting pin on the castor
wheel (13) into the designated mounting hole on the underside of the
base (12). Firmly push the castor wheels (13) into the mounting holes
(Fig B).
NOTE: Take care not to damage the castor wheel.
They do not need to be forced into position.
3. When all 4 castor wheels (13) are tted, turn
the product the right way up, and re-attach
the appliance head (2) ensuring you align the
notches on the ridge of the tank lip with the
side locking handles, and secure the 2 side
locking handles (6) in position (Fig C).
Assembly of the Carry Handle
1. Place the carry handle (1) in the grooves on
the top of the appliance head (2) so that they
are tted and align correctly (Fig D).
2. Using a phillips screwdriver, insert and secure
the screws through each side of the handle until
secure (Fig E).
Assembly for Dry Vacuuming –
HEPA Filter
WARNING: Never use the vacuum without
a lter. Check that the lter is securely tted
at all times.
The Wet and Dry Vacuum is tted with the HEPA
lter (16) used for dry vacuuming upon purchase.
To continue assembly for dry vacuuming, continue
to the ‘Fitting the exible hose’ section on page 15.
Assembly Assembly
Assembly
B.
D.
A.
C.
Notch
E.
Tighten
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Workzone MWW706S-35L wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info