Bedienungsanleitung Workzone MWW706S-35L (Seite 9 von 16) (Englisch)

724654

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

2400W Wet & Dry Vacuum

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL No.: MWW706S-35L-1200WC • 06/2018 • 61406

(toll free)

AFTER SALES SUPPORT

(toll free)

2400W Wet & Dry Vacuum

e-mail: help@powertoolsupport.com1800 909 909

MODEL No.: MWW706S-35L-1200WC • 06/2018 • 61406

14 15

Assembly Assembly

Assembly for Wet Vacuuming – Foam Filter

WARNING: Never use the vacuum without a lter. Check that the lter

is securely tted at all times.

1. Remove the appliance head (2) from the tank (10) by unlocking the 2 x

side locking handles (6) pulling them outwards, then upwards (Fig A).

Place the appliance head (2) upside down onto a at surface, or on its side

(if the carry handle is already assembled).

2. Remove the HEPA lter (16) (installed upon purchase) by pulling it away

from the appliance head (2) (Fig F).

3. Slip the foam lter (19) over the lter basket (14) (Fig.G). Ensure the foam

lter (19) covers the full lter basket (14) (Fig H).

NOTE: The foam lter (19) is only suitable for WET vacuuming.

IMPORTANT: Regularly clean the foam lter (19) and allow it to dry before

resuming vacuuming.

IMPORTANT: DO NOT use the HEPA lter for wet vacuuming (the HEPA

lter is pre-installed upon purchase).

IMPORTANT: The Wet and Dry Vacuum should only be connected

to a mains power supply socket; an RCD (Residual Current Device) is

recommended.

4. Re-assemble the appliance head (2) back onto the tank (10), and secure

the 2 x side locking handles (6).

NOTE: Always unplug the appliance after use and before cleaning or

changing the lters or accessories.

Fitting the Flexible Hose

Connect the exible hose (17) to the exible hose

outlet depending on the application required:

1. Vacuuming

Connect the exible hose (17) to the exible

hose outlet – suction (7) by inserting into the

outlet and aligning the arrow and locking pin

on the end of the exible hose (17), with the

arrow and ridge on the top of the exible hose

outlet – suction (7). This should ensure the

locking pin on the exible hose (17) aligns

with the ridge in the exible hose outlet –

suction (7). Rotate the exible hose (17) to the

left to secure the hose into position (Fig I/J)

2. Blowing

Connect the exible hose (17) to the exible

hose outlet – blowing (8) by inserting into the

outlet and aligning the arrow and locking pin

on the end of the exible hose (17), with the

ridge on the top of the exible hose outlet –

blowing (8). This should ensure the locking pin

on the exible hose (17) aligns with the ridge

in the exible hose outlet – blowing (8). Rotate

the exible hose (17) to the left to secure the

hose into position (Fig K/L)

G.F.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone MWW706S-35L Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info