Bedienungsanleitung Workzone Q1W-SP14-1900A (Seite 8 von 16) (Englisch)

734948

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

14 15

www.coreservice.co.uk

AFTER SALES SUPPORT

IRE

+353 (0) 19022605

www.coreservice.co.uk

AFTER SALES SUPPORT

IRE

+353 (0) 19022605

Q1W-SP14-1900A

+44 (0) 190 472 7501

Fitting the water intake adapter (Figure 6)

• Remove the protective cap from the threaded connector of the high-pressure washer

and screw the adapter for the water intake (14) onto the threaded connector, hand-

tightened.

NOTE

Take good care of the protective caps for the storage of the machine.

Connecting the intake hose to the machine (Figure 7)

• Connect the intake hose to the high-pressure washer with a quick-action coupling

(notincluded in the scope of supply) using the adapter for the water intake (11).

Connecting the intake hose to the water supply (Figure 8)

WARNING

The machine may not be connected directly to the drinking water supply.

Inthis case, use a water backow preventer or an intake hose set approved

inaccordance with IEC 61770.

• Connect the intake hose to the water supply and open the intake valve. The temperature

of the water may not exceed 40 °C.

Switching o the mains switch (Figure 9)

• Ensure that the ON/OFF switch on the machine is switched off

(at the OFF position).

Creating a mains connection (Figure 10)

• Insert the mains plug into a correctly installed socket with an earthing contact with

anAC voltage supply in accordance with the machine's rating plate.

Operation

WARNING

Familiarise yourself with all the operating features before putting the

machine into operation. Ensure before use that the machine is in proper

working order.

Wear suitable clothing, as well as ear protectors and goggles when working

with the machine.

Check that the machine is in a safe state:

• Inspect the machine and accessories for visible damage.

• Check that all the parts of the machine are securely fixed in place.

• Check that there are no leaks from the water connection and high-pressure pipes.

Starting and stopping

ATTENTION

Never operate the machine without water because the pump may damage if

run dry. If the intake water is impure, use a water lter.

Starting

1. Open the valve for the water intake. (Figure 8)

2. Disengage the yellow safety catch on the spray gun by pushing it down until it

clicks in place.

3. Press the trigger until a steady stream of water is discharged. (Figure 11) Then

release the trigger.

4. Set the ON/OFF switch to ON in order to switch on the machine. (Figure 12)

5. Press the trigger again to commence the cleaning work.

Stopping

1. Release the trigger.

2. Set the ON/OFF switch to OFF in order to switch off the machine. (Figure 9)

3. Briefly press the trigger until the machine is depressurised.

4. Lock the trigger by flipping the yellow safety catch up until it becomes engaged.

(Figure 13) This prevents it from being started again inadvertently.

5. Close the valve for the water intake.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone Q1W-SP14-1900A Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Workzone Q1W-SP14-1900A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info