Bedienungsanleitung Workzone Q1W-SP14-1900A (Seite 10 von 16) (Englisch)

734948

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

18 19

www.coreservice.co.uk

AFTER SALES SUPPORT

IRE

+353 (0) 19022605

www.coreservice.co.uk

AFTER SALES SUPPORT

IRE

+353 (0) 19022605

Q1W-SP14-1900A

+44 (0) 190 472 7501

• Pull the nozzle head forward to lower the pressure and push the nozzle head back to

raise the pressure. (Figure 15)

By turning the nozzle head through 180°, you can adjust the width of the jet from

spot jet to at jet:

• Turn the nozzle head counterclockwise to set a spot jet. The further you turn the

nozzle head in a clockwise direction, the wider the flat jet becomes. (Figure 16)

NOTE

The spot jet is especially suitable for cleaning very soiled, narrow places,

whereas the at jet is ideal for cleaning wide areas.

Using the turbo lance

The turbo lance (9) creates a rotating jet of water which can be used to remove

stubborn dirt.

ATTENTION

When you use the turbo lance, there is a very great risk of damaging sensitive

surfaces. Apply it carefully, starting o with a large working distance and

reducing it as required.

• Stop the machine and switch the ON/OFF switch to OFF.

• Press the trigger on the spray gun briefly to reduce the system pressure.

• Insert the turbo lance instead of the spray lance. (Figure 4)

Using the rotating brush

The rotating brush (8) is a tool for cleaning surfaces with care. The brush is driven here

by the high-pressure jet, and the water only strikes the surface being cleaned at low

pressure.

The cleaning eect is achieved by the action of the brush, and the loosened dirt is

washed away by the water.

• Stop the machine and switch the ON/OFF switch to OFF.

• Press the trigger on the spray gun briefly to reduce the system pressure.

• Insert the rotating brush instead of the spray lance or the turbo lance.

(Figure 5)

Automatic feed of detergents

WARNING

Only use the detergents supplied or recommended by the manufacturer.

Thesafety of the machine may be adversely aected if you use other

detergents or chemicals.

Following direct contact between the detergent and your skin or mucous

membrane, rinse with lots of clear water and seek medical attention,

ifnecessary.

This high-pressure washer is equipped with a device for automatically feeding

detergents to the jet of water. Procedure for using this function:

• Lock the trigger on the spray gun by flipping the yellow safety catch up until it

becomes engaged. (Figure 13)

• Remove the sealing cap from the detergent tank (1) on the back of the machine and

pull the hose out. (Figure 14)

• Take the detergent tank o the bracket and ll it with detergent.

• Place the detergent tank back onto the bracket, reinsert the hose and replace the

sealing cap.

• Fit the adjustable spray lance (10) onto the spray gun.

• Set the nozzle head to the low pressure position by pulling it forward. (Figure 15)

• Disengage the safety catch and press the trigger on the spray gun to start work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone Q1W-SP14-1900A Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Workzone Q1W-SP14-1900A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info