Bedienungsanleitung Workzone TG212T (Seite 13 von 18) (Englisch)

724649

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018

24 25

B. Contact Firing

1. Once the single/contact ring slider knob (9) is set to contact ring,

depress the trigger switch (6) (Fig U), and then depress the safety striker

pin ush on the contact surface to re a single nail / staple (Fig T).

2. Keeping your nger pressed on the trigger switch (6), lift the Brad

nailer / stapler away from the contact surface, hence also releasing the

safety striker pin (1), and place in the next position for the next nail or

staple to be red, again depressing the safety striker pin ush onto the

contact surface. The Brad nailer / stapler will automatically re another

staple or nail again (Fig V).

3. Repeat the process keeping your nger pressed on the trigger switch

(6), to continually re each nail/staple.

NOTE: The safety striker pin (1) MUST be depressed at the same time as

continually pressing the trigger switch (6), otherwise the Brad nailer /

stapler will not re / function.

WARNING: Do not keep the trigger switch (6) depressed when

the tool is not in use to prevent accidental ring.

Using the LED Worklight/s while using the

Brad Nailer / Stapler

CAUTION! LED is laser class 1! Do not look directly into the laser as this

may result in damage to the eyes.

1. To turn on the LED worklights while on the Brad nailer / stapler, press

on the LED worklight switch (7) before pressing on the trigger switch

(6) (Fig W/X).

Removing jammed Nails / Staples

1. If the LED battery and function indicator (10) is ashing red (Fig N)

this indicates a jam in the magazine.

2. Remove the battery from the Brad nailer / stapler.

3. Open the magazine by pressing on the magazine release latch (14)

(Fig Y), and remove the nail or staple cartridge and the jammed nail or

staple (Fig Z).

4. Re-install nails or staples, re-install battery, and check the jam is

corrected. If corrected, the red light will be no longer ashing on the

LED battery and function indicator (10).

5. If the jam is still not corrected it means a nail or staple may be jammed

in the internal striking mechanism.

6. Remove the battery from the Brad nailer / stapler, then using the

supplied 3mm hex key (19), remove the 4 x hex screws located in front

of the depth adjustment wheel and remove the nosepiece. Remove the

jammed nail / staple; this may require using pliers (Fig AA).

7. When the jam is removed, reattach the nose

piece and resecure the 4 x hex screws using

the supplied 3mm hex key (19). Re-install nails

or staples, re-install battery, and check the jam

is corrected. If corrected, the red light will be

no longer ashing on the LED battery and

function indicator (10).

V. W. X.

Z. AA.

JAM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone TG212T Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info