Bedienungsanleitung Workzone TG212T (Seite 11 von 18) (Englisch)

724649

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018

20 21

Ensure the end of the staple cartridge engages inside the guide rails at

the end of the magazine (Fig H).

3. Push the magazine (11) closed by pushing it up towards the safety

striker pin (1) end of the magazine until it closes securely (Fig I). The

magazine release latch (14) will engage and a “click” will be heard when

secure (Fig J).

B. Loading Nails

NOTE: Do not install nails of dierent sizes at the same time. Only 1 x

cartridge of the same size nail should be installed at each use. Loading

various nail sizes at one time will cause malfunction and void your warranty.

1. Press on the magazine release latch (14), to open the magazine (11)

(Fig E), ensuring you extend it out as far as it will release (Fig F).

2. To load nails, insert the cartridge of nails with the heads of the nails

facing to the top rear of the open magazine with the nail points facing

away (Fig K). Ensure the end of the nail cartridge engages inside the

guide rails at the end of the magazine (Fig H).

3. Push the magazine (11) closed by pushing it up towards the safety striker

pin (1) end of the magazine until it closes securely (Fig I). The magazine

release latch (14) will engage and a “click” will be heard when secure

(Fig J).

Depth Adjustment Wheel

WARNING: Keep the tool pointed away from yourself and others

when setting the depth adjustment. Failure to do so could result in

possible serious personal injury.

WARNING: Ensure to remove battery pack from the tool during

initial depth adjustment setting.

The depth adjustment wheel (3) (Fig L) is used for setting the depth of the

nail or the staple from the workpiece contact (nail/staple release) (2).

On each side of the depth adjustment wheel (3) is a symbol indicating

whether turning the wheel in that direction will increase or decrease the

nail / staple depth (Fig M). The range of the depth adjustment wheel (3)

is approx. 3mm.

1. When viewing the depth adjustment wheel (3) per Fig M, turning the

depth adjustment wheel (3) to the left will increase the depth of the nail

/ staple into the contact surface. If pushing all the way to the left, the nail

will be ush on the contact surface.

2. Turning the depth adjustment wheel (3) to the right will decrease the

depth of the nail / staple into the contact surface.

3. It is recommended to test the depth of adjustment doing a few test

shots, and then adjusting the wheel accordingly to reach the desired

depth required for the contact surface. Proceed to the next page for

Operation to start your product and check the adjustment.

H. I. J.

K. L. M.

“CLICK”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone TG212T Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info