Bedienungsanleitung Workzone TG212T (Seite 9 von 18) (Englisch)

724649

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018

16 17

Important information – Product care

NOTE: Xnity Battery and Charger not included. For any issues related

directly to your purchased ALDI Xnity Battery / charger, contact the

Customer Service of the manufacturer as listed on the battery / charger

packaging, manual or on the label on the battery / charger.

This Brad Nailer / Stapler uses Lithium Ion Battery Cells. Care MUST be taken to

ensure both the safety and life of the pack is maintained. Ensure you have read all

of the safety notes in the previous pages before using the Brad Nailer / Stapler.

Treat the battery pack with care and within the guidelines of this manual and the

supplied manual included with the purchase of ALDI Xnity Battery/s.

If the battery pack does become immersed in water or any uids, or is subject

to a severe drop or it does not operate within the guidelines of this manual

or the supplied manual included with the purchase of ALDI Xnity Battery/s,

immediately STOP using the battery pack and have it checked. During operation

avoid overloading the Brad Nailer / Stapler. If the Brad Nailer / Stapler is

overloaded it will automatically STOP. Overloading may occur for a number of

reasons including when the Brad Nailer / Stapler is pushed too hard or when

using a Nail / Staple greater than what is specied, or there is a nail / staple jam. If

you do overload the Brad Nailer / Stapler during operation refer to the “Overload

Protection” section in this manual.

NOTE: When the battery of the Brad Nailer / Stapler is at the lower end of the

charge, the Brad Nailer / Stapler is more susceptible to the overload condition.

Running the Brad Nailer / Stapler at close to maximum load, or continual resetting

of the overload will cause the battery pack to overheat. When a preset cell

temperature is detected, the battery pack will automatically STOP operating and

will not restart until the battery pack has cooled to a safe level.

In this condition, DO NOT force the cooling down of the pack by placing in a

freezer or similar device. Refer to the “Overload Protection” section in this manual.

Another feature of the Brad Nailer / Stapler is the low voltage cut out feature. This

feature operates when the voltage drops below a preset value. When this occurs

the tool will automatically stop operating. To correct the situation you need to

either insert another charged battery into the Brad Nailer / Stapler or recharge the

existing battery, and then proceed with the Brad Nailer / Stapler application.

NOTE: Attempting to restart the tool in this condition without either recharging

the battery or installing a battery with charge will lead to Brad Nailer / Stapler

restarting and then stopping again after only a few seconds of operation.

These safety devices have been tted for the safety, reliability and life of the tool.

Assembly

Fitting and removing the Battery from the Brad Nailer /

Stapler and Charger.

NOTE: (Xnity Battery pack and charger is not included with

this product; it is shown only for illustrative and instructional

purposes only)

1. To install your purchased Xnity battery (17) on to the Brad Nailer /

Stapler, align the grooved guide rails of the battery (17) with the raised

guide rails on the bottom of the Brad Nailer / Stapler. With your thumb

on the battery release tab on the battery pack, slide it rmly into the

handle until the battery is secure in position (Fig A). Release your thumb

from the battery release tab. When the battery is secured you will hear it

engage with a snap / click.

2. To remove the battery (17) from the Brad Nailer / Stapler, press the

battery pack release button and slide the battery (17) completely out

and away from the Brad Nailer / Stapler (Fig B).

3. When applying the battery (17) onto your purchased Xnity charger

(18), align the grooved guide rails of the battery (17) with the raised

guide rails on the charger (18) (Fig C). The charger (18) will make a snap

/ click noise when it is securely aligned.

A. B.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone TG212T Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info