Bedienungsanleitung Worx WG368E.9 (Seite 19 von 204) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

576045

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

Cordless Chain Saw EN

SAW MAINTENANCE AND

KICKBACK SAFETY

Follow maintenance instructions in this manual.

Proper cleaning of saw and chain and guide bar

maintenance can reduce chances of kickback.

Inspect and maintain saw after each use. This

will increase the service life of your saw.

NOTE: Even with proper sharpening, risk of

kickback can increase with each sharpening.

MAINTENANCE AND

STORAGE OF CHAIN SAW

1. Remove the battery pack from the saw

• When not in use.

• Before moving from one place to another

• Before servicing.

• Before changing accessories or attachments,

such as saw chain and guard bar.

2. Inspect chain saw before and after each

use. Check saw closely if guard or other part

has been damaged. Check for any damage

that may affect operator safety or operation

of saw. Check for alignment or binding of

moving parts. Check for broken or damaged

parts. Do not use chain saw if damage affects

safety or operation. Have damage repaired

by authorized service center. To locate an

authorized service center, visit

www.worx.com

3. Maintain chain saw with care.

• Never expose saw to rain.

• Keep chain sharp, clean, and lubricated for

better and safer performance.

• Follow steps outlined in this manual to

sharpen chain.

• Keep handles dry, clean, and free of oil and

grease.

• Keep all screws and nuts tight.

4. When servicing, use only identical

replacement parts.

5. When not in use, always store chain saw

• In a high or locked place, out of children’s

reach.

• In a dry place.

BAR MAINTENANCE

To maximize bar life, the following bar

maintenance is recommended.

The bar rails that carry the chain should be

cleaned before storing the tool or if the bar or

chain appear to be dirty.

The rails should be cleaned every time the

chain is removed.

Turn the bar over, top rail becoming bottom

and bottom rail becoming top, around every 5

hours of use.

TO CLEAN THE BAR RAILS:

1. Remove chain cover and bar and chain.

(see section ASSEMBLY)

2. Using a wire brush, screwdriver or similar

suitable tool, clear the residue from the

rails of the bar. (See Fig. V)

3. Make sure to clean oil passages

thoroughly.

CONDITIONS WHICH REQUIRE GUIDE

BAR MAINTENANCE:

• Saw cuts to one side or at an angle.

• Saw has to be forced through the cut.

• Inadequate supply of oil to the bar and

chain.

Check the condition of the guide bar each time

the chain is sharpened. A worn guide bar will

damage the chain and make cutting difﬁcult.

After each use, with unit disconnected from

power source, clean all sawdust from the

guide bar and sprocket hole.

When rail top is uneven, use a ﬂat ﬁle to

restore square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove Correct Groove

Replace the guide bar when the groove is

worn, the guide bar is bent or cracked, or

when excess heating or burring of the rails

occurs. If replacement is necessary, use only

the guide bar speciﬁed for your saw in the

repair parts list or on the decal located

on the chain saw.

REPLACING BAR & CHAIN

Fit the chain and guide bar as described in

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WG368E.9 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info