Bedienungsanleitung Worx WX22AG (Seite 12 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575102

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Angle grinder EN

1312

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for cutting,

roughing and brushing metal and stone

materials without using water. For cutting

metal, a special protection guard for cutting

(accessory) must be used.

1. LOCK-OFF & LOCK-ON SWITCH

(See Fig. A)

Your switch is locked off to prevent accidental

starting. To switch on your tool, push the

safety switch lever (B) forward and depress

on/off switch (A) fully. Now your tool is switch

on. To switch off your tool, just release the On/

Off switch.

If you wish to use the tool continuously,

push the safety switch lever (B) forward and

depress on/off switch (A) fully, then push

the safety switch lever (B) forward again and

release the On/Off switch. Now your switch

has been locked on for continuously use.

To switch off your tool, simply depress On/

Off switch fully, the safety On/Off switch will

automatically release.

Restarting protection

The restarting protection feature prevents

uncontrolled restarting of the machine after an

interruption in the power supply.

To restart the operation, switch the On/Off

switch (A) to the Off position and start the

machine again.

2. HAND GRIP AREAS

Always hold your angle grinder ﬁrmly with

both hands when operating (See Fig. B).

3. ANTI-VIBRATION AUXILIARY HANDLE

This front handle incorporates a ﬂexible

vibration absorbing mounting between the

bolt and handle grip to reduce vibration and

increase comfort.

NOTE: the handle ﬁxing to the gear case is

ﬂexible and not a rigid clamp. You have the

option of three working positions to provide

the safest and most comfortable control of

your angle grinder (See Fig. C). Side position

for grinding and top position for cutting. The

handle is screwed clockwise into the gear case

hole (See Fig. B). Always use the auxiliary

handle.

4. SPINDLE LOCK BUTTON

Must only be used when changing a disc.

Never press when the disc is rotating!

5. DISC FITTING

The inner ﬂange (5) is located over the spindle

(6) and on the two spindle ﬂats. Locate the

disc onto the inner ﬂange and then the

outer ﬂange (7) is screwed onto the spindle.

Press the spindle lock button (4) and rotate

the spindle until it locks, then ﬁrmly tighten

the outer ﬂange using your pin spanner to

clamp the disc (See Fig.D). The pins on your

pin spanner locate in the holes on the outer

ﬂange. Check the disc rotates freely and is

securely clamped. Make a no load test run

for 30 seconds to check disc vibration and

disc run out. To remove a disc, reverse these

instructions.

6. ADJUSTABLE OUTER FLANGE

CLAMPING

The outer ﬂange (7) should be adjusted to suit

different disc thickness. For thinner cutting

or diamond discs the raised part of the outer

ﬂange is ﬁtted facing away from the disc (See

Fig. E.2). For thicker grinding discs the raised

part of the outer ﬂange is ﬁtted facing towards

the disc to provide improved support for the

disc hole (See Fig. E.1). Always ensure your

disc is securely clamped.

7. GUARD ADJUSTMENT (See Fig. F)

Before any work on the machine itself,

pull the mains plug.

For work with grinding or cutting discs,

the wheel guard must be mounted.

Wheel Guard for Grinding

The coded projection on the wheel guard (14)

ensures that only a guard that ﬁts the machine

type can be mounted.

Open the clamping lever (8). Place the wheel

guard (14) with coded projection into the

coded groove on the spindle of the machine

head and rotate to the required position

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX22AG Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info