Bedienungsanleitung Worx WX22AG (Seite 13 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575102

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Angle grinder EN

1312

(working position).

To fasten the wheel guard (14), close the

clamping lever (8).

The closed side of the wheel guard (14)

must always point to the operator.

NOTE: with the clamping lever (8) open the

clamp adjusting nut (9) can be adjusted to

ensure the guard is securely clamped after the

clamping lever (8) is ﬁnally closed.

Wheel Guard for Cutting

WARNING!

For cutting metal, always

work with the wheel guard for cutting.

The wheel guard for cutting (15) is mounted in the

same manner as the wheel guard for grinding.

8. REMOVING THE GUARD

Never remove your guard for any other

working conditions. To remove, ﬁrst take

off the disc and both ﬂanges. Then open the

clamping lever (8) and rotate the guard to

align the projections with the gear case cut

outs, then remove the guard. To re-ﬁt the

guard, repeat this process in reverse. Keep all

parts in a safe place.

9. SOFT START

Internal electronic components allow the

motor speed to increase slowly, which reduces

the“twisting”effect on your wrists due to the

high power motor.

10. ROTATING THE GEAR CASE

For special working situations, the gear

case can be rotated 90o to improve working

comfort and safety. First, disconnect from the

mains supply then remove the disc and guard.

Remove the 4 x screws from the gear case

(See Fig.G). Carefully rotate the gear case in

your desired direction but do NOT pull the

gear case out of the housing. If the gear case

comes out of the housing the motor carbon

brushes will need replacing.

11. TO USE THE GRINDER

ATTENTION: Do not switch the

grinder on whilst the disc is in

contact with the workpiece. Allow the

disc to reach full speed before starting

to grind.

Hold your angle grinder with one hand on the

main handle and other hand ﬁrmly around the

auxiliary handle.

Always position the guard so that as much of

the exposed disc as possible is pointing away

from you.

Be prepared for a stream of sparks when the

disc touches the metal.

For best tool control, material removal

and minimum overloading, maintain an

angle between the disc and work surface of

approximately 15

-30

when grinding.

Use caution when working into corners as

contact with the intersecting surface may

cause the grinder to jump or twist.

When grinding is complete allow the workpiece

to cool. Do not touch the hot surface.

12. CUTTING

WARNING! For cutting metal, always

work with the wheel guard for cutting.

When cutting, do not press, tilt or oscillate the

machine. Work with moderate feed, adapted to

the material being cut.

Do not reduce the speed of running down

cutting discs by applying sideward pressure.

The direction in which the cutting is performed

is important.

The machine must always work in an up-

grinding motion. Therefore, never move the

machine in the other direction! Otherwise, the

danger exists of it being pushed uncontrolled

out of the cut.

13. BRUSH WEAR INDICATOR (WX22AG

WX23AG WX23AG.2) (See Fig. H)

Your angle grinder is ﬁtted with an automatic

brush wear indicator. A green led indicates

that the brush condition is normal. A red led

indicates that the brush is coming to the end

of its useful life and should be replaced as

soon as possible.

14. AUTO-STOP CARBON BRUSH (ONLY

FOR WX23AG.1) (See Fig. I1)

When the resin insulating tip (17) inside the

carbon brush (18) is exposed to contact the

commutator (16), it will automatically shut

off the motor. When this occurs, both carbon

brushes should be replaced. Keep the carbon

brushes clean and free to slip in the holders.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX22AG Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info