Bedienungsanleitung Worx WX429 (Seite 14 von 20) (Englisch)

673175

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Compact Circular Saw WX429

electric shock.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord

may be cut or snagged and your hand or

arm may be pulled into the spinning wheel.

n) Never lay the power tool down until

the accessory has come to a complete

stop. The spinning wheel may grab the

surface and pull the power tool out of your

control.

o) Do not run the power tool while

carrying it at your side. Accidental

contact with the spinning accessory could

snag your clothing, pulling the accessory

into your body.

p) Regularly clean the power tool’s

air vents. The motor’s fan will draw the

dust inside the housing and excessive

accumulation of powdered metal may

cause electrical hazards.

q) Do not operate the power tool near

ﬂammable materials. Sparks could ignite

these materials.

r) Do not use accessories that require

liquid coolants. Using water or other

liquid coolants may result in electrocution

or shock.

KICKBACK AND RELATED

WARNINGS

Kickback is a sudden reaction to a pinched or

snagged rotating wheel. Pinching or snagging

causes rapid stalling of the rotating wheel

which in turn causes the uncontrolled power

tool to be forced in the direction opposite of

the wheel’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged

or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can

dig into the surface of the material causing

the wheel to climb out or kick out. The wheel

may either jump toward or away from the

operator, depending on direction of the

wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

a) Maintain a ﬁrm grip on the power tool

and position your body and arm to

allow you to resist kickback forces.

Always use auxiliary handle, if provided,

for maximum control over kickback or

torque reaction during start-up. The

operator can control torque reactions or

kickback forces, if proper precautions are

taken.

b) Never place your hand near the

rotating accessory. Accessory may

kickback over your hand.

c) Do not position your body in line with

the rotating wheel. Kickback will propel

the tool in direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working

corners, sharp edges etc. Avoid

bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain,

woodcarving blade, segmented

diamond wheel with a peripheral

gap greater than 10 mm or toothed

saw blade. Such blades create frequent

kickback and loss of control.

f) Do not “jam” the wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the

loading and susceptibility to twisting or

binding of the wheel in the cut and the

possibility of kickback or wheel breakage.

g) When wheel is binding or when

interrupting a cut for any reason,

switch off the power tool and hold the

power tool motionless until the wheel

comes to a complete stop. Never

attempt to remove the wheel from the cut

while the wheel is in motion otherwise

kickback may occur. Investigate and take

corrective action to eliminate the cause of

wheel binding.

h) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut. The

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX429 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info