Bedienungsanleitung Worx WX523 (Seite 14 von 19) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575058

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

20V WORX saw EN

diamond wheel with a peripheral

gap greater than 10 mm or toothed

saw blade. Such blades create frequent

kickback and loss of control.

f) Do not “jam” the wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the

loading and susceptibility to twisting or

binding of the wheel in the cut and the

possibility of kickback or wheel breakage.

g) When wheel is binding or when

interrupting a cut for any reason,

switch off the power tool and hold the

power tool motionless until the wheel

Comes to a complete stop. Never

attempt to remove the wheel from the cut

while the wheel is in motion otherwise

kickback may occur. lnvestigate and take

corrective action to eliminate the cause of

wheel binding.

h) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

i ) Support panels or any oversized

workpiece to minimize the risk of

wheel pinching and kickback. Large

workpieces tend to sag under their own

weight. Supports must be placed under the

workpiece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.

j) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical

wiring or objects that can cause kickback.

GENERAL SAFETY

WARNINGS FOR YOUR

LASER

WARNING: Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result in

serious injury.

Save all warnings and instructions for

future reference.

These lasers do not normally present an

optical hazard although staring at the

beam may cause ﬂash blindness.

Do not stare directly at the laser beam. A

hazard may exist if you deliberately stare

into the beam, please observe all safety

rules as follows:

1) The laser shall be used and maintained

in accordance with the manufacturer’s

instructions.

2) Never aim the beam at any person or

an object other than the work piece.

3) The laser beam shall not be

deliberately aimed at another person

and shall be prevented from being

directed towards the eye of a person

for longer than 0.25 seconds area.

4) Always ensure the laser beam is

aimed at a sturdy work piece without

reﬂective surfaces, e.g. wood or

rough-coated surfaces are acceptable.

Bright shiny reﬂective sheet steel or similar

is not suitable for laser applications as the

reﬂective surface may direct the laser beam

back at the operator.

5) Do not change the laser device with

a different type. The manufacturer or an

authorized agent must carry out repairs.

6) CAUTION: Use of controls or adjustments

other than those speciﬁed herein may

result in hazardous radiation exposure.

ADDITIONAL SAFETY WARNING FOR

CLASS 2 LASER

The laser device ﬁtted to this tool is CLASS

2 with a maximum radiation of 1.5mW and

650nm wavelength.

CLASS 2 LASER RADIATION, DO NOT

STARE INTO BEAM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX523 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info