Bedienungsanleitung Worx WX570 BLADERUNNER (Seite 14 von 143) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575088

Zoom out

Zoom in

Vorherige Seite

1/143

Nächste Seite

Multi-function saw EN

without the guard arm assembly ﬁtted

and correctly lowered to guard and

guide the blade.

3. CROSS CUT (See Fig. J)

— MAKING A CROSS CUT:

(a) Set the miter gauge to 0° and tighten

locking knob. Insert miter gauge shaft to

miter slot.

(b)

Lower the guard arm to make the pressure

foot (6) contact the work piece. Then lower

the quick release lever (7). Make sure the

pressure foot is ﬁrmly against the work piece.

4. RIP CUT (See Fig. K)

— MAKING A RIP CUT:

(a) Set and lock the miter gauge at 0˚using the

angle knob.

(b) Slide the miter gauge into the fence slot

(12), located perpendicularly to the miter

slot (14).

NOTE:

The fence can be set to the left or

right of the blade, a larger off-cut can be

accommodated if the fence is set to the right.

the pointer in front of the blade.

NOTE:

The miter gauge must always be

locked at 0˚ for a rip cut, any other fence angle

will cause the work to jam between the fence

and blade.

(d) Carry out the cut as described in general

cutting rules.

5. MITER CUT (See Fig. L)

MAKING A MITER CUT:

(a) Follow the same procedures as you would

for a cross cut. Set the miter gauge to

desired angle and tighten the lock knob.

NOTE:

Make sure to slide the miter gauge into

the miter slot (14), not the fence slot (12).

6. INTERNAL CUT (See Fig. M)

BladeRunner

is ideal for making inside cuts

for detail work. To make an inside cut:

(a) Drill a pilot hole in your workpiece. Make

sure the diameter of the hole is larger than

the blade you will use.

(b) Make sure the saw is unplugged. Slacken

the guard arm clamp knob and raise the

guard arm (See Fig. B1).

hole in your workpiece.

(d) Lower the guard arm to make the pressure

foot contact the workpiece. Then lower the

quick release lever. Make sure the pressure

foot is ﬁrmly against the workpiece.

(e) Perform the cut according to general

cutting rules.

(f) At the completion of the cut, again unplug

the saw; raise the guard arm to remove the

work.

(g) Always remember to return the guard arm

to the lowered position when ﬁnished.

7. DUST COLLECTION (See Fig. N & Q)

Dust and chips from cutting will be collected in

the dust drawer at the bottom of the machine.

NOTE: To ensure optimal dust collection,

empty the dust drawer (17) when it becomes

ﬁlled to approximately 2/3 of its capacity.

For better cut line visibility and cleaner

working environment, connect a vacuum

cleaner or dust extractor to the vacuum port

(11) on the blade guard.

A vacuum MUST be used for hazardous dusts

such as tile cutting.

8. CARRY HANDLE (See Fig. O)

BladeRunner

has a built-in carrying

handle (3) on the side for easy, convenient

transporting from one job site to another.

Before carrying the saw, shut off the power

and pull out the plug.

NOTE:

(a) When carrying the saw, accessories shall

be stored properly or locked up to avoid

being lost.

(b) Before carrying the saw, please empty the

dust drawer.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

There are no user serviceable parts in your

power tool. Never use water or chemical

cleaners to clean your power tool. Wipe clean

with a dry cloth. Always store your power

tool in a dry place. Keep the motor ventilation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX570 BLADERUNNER Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info