Bedienungsanleitung Worx WX625 (Seite 10 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575097

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Perpendicular planer EN

11 10

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for planning of ﬁrmly

supported wooden materials, such as beams

and boards. It is also suitable for beveling

edges and rebating.

1. SAFETY ON/OFF SWITCH

The switch is locked off to prevent accidental

starting. Depress the lock off button (2) then

on/off switch (1) and release lock off button

(2). The machine is working now. To switch off

,just release the on/off switch. (See Fig. A)

2. CUTTING DEPTH ADJUSTMENT

Smaller cutting depth of 0-1mm (Max. 2.0mm)

is best for most surface planning or rebating.

Rotate the cutting depth adjustment (4) to

set the required cutting depth on the scale,

Scale graduation = 0.125mm. The clockwise

rotation increases the planning depth;

the counterclockwise rotation reduces the

planning depth. (See Fig. B)

3. ADJUST DUST EXTRACTION AND

CHIP EJECTION

Dust extraction can be adjusted to the right

or left side by manually. Rotate one end of

the dust extraction (5) until it stops (See Fig.

C). The arrowhead on the dust extraction

indicates the dust extraction direction.

NOTE: Due to the size and material

of some wood shavings e.g. wet or

hard wood it is possible for the dust

extraction to become blocked. Remove

the plug from the mains power supply,

then using a wooden stick clear the

blocked dust extraction.

4. BASEPLATE STAND

Uplift the rear of the planer, the base plate

stand (6) can make the machine to be set

down directly and protect the cutting blades

from any damage and the blades from

damaging the surface (See Fig. D). When

planning, the stand will be pushed away by

the end of the wood. Always check the stand is

free to move on the base plate (See Fig. E).

5. BLADE FITTING AND CHANGING

WARNING: Remove power cord

from the socket before carrying out

any adjustments or changing blades.

The blade has two cutting edges, which can

be reversed .When replacing or reversing the

plane blades, the guide groove guarantees

constant height adjustment.

NOTE: Dull and worn blade cannot be

reground and must be replaced.

Remove the plug from the mains socket.

Using the spanner (19) provided loosen the

3 bolts approximately 1/2 rotation counter-

clockwise (See Fig. F). Holding the blade

clamp (7) in position, using a piece of wood

slides the blade (8) out of the blade clamp (7)

to remove the blade from the blade clamp

(See Fig. F)

NOTE: There is no need to remove the

blade clamp (7) as this can change the

factory settings for cutting blade height

control. Before reinserting a new or reverse

blade, always clean both the blade and the

blade seat if dirty. Slide the blade into the

blade clamp in the correct orientation. Check

the blade is equal with the clamp. When

tightening the screws (10) ensure the correct

tightening sequence (

). Before

starting, rotate by hand to check the roller is

free to rotate.

Rotate the blade head by a further 180

and

repeat the procedure disassembling the

second plane blade.

6. REPLACING A DRIVE BELT

WARNING:

1) Remove the plug from the socket

before carrying out any adjustment,

servicing or maintenance.

2) The cutting blades will be turning and

may cause injury.

Loosen screw and remove belt cover (11),

remove worn drive belt from large pulley

(13)

and pinion (12) and clean them (See Fig. G).

Lace the new drive belt on the top of pinion

and turning it manually, press it on the large

pulley (13) (See Fig. H).Make sure the drive

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX625 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info