Bedienungsanleitung Worx WX671.3 (Seite 11 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575135

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

High frequency multi-function tool EN

6. MOUNTING THE SUCTION DEVICE

(See Fig. C,D)

When vacuuming, mount the suction device

as shown in C1-D2.

NOTE: Using the sanding pad perforated. You

can only do the vacuuming after ﬁtting the

dust collector.

7. SANDING

Typical application: wood, metal; small areas,

especially corners, edges and places difﬁcult

to access.

Select high oscillation frequency.

Sand with a constant movement and light

pressure.

Heavy pressure does not increase the removal

– The sanding sheet merely wears faster.

8. SAWING WITH THE SEGMENT SAW

BLADE

Typical application: wood, plastics, sheet

metal.

Select high oscillation frequency.

The saw blade lasts longer if the wear

is distributed evenly. To ensure an even

distribution, loosen the saw blade, rotate it

and retighten ﬁrmly.

9. SAWING WITH THE UNIVERSAL END

CUT SAW BLADE (See Fig. E)

WARNING: The sawing teeth are

very sharp. Do not touch during

mounting and application.

The workpiece must be inserted ﬁrmly or

clamped tightly before it is cut.

Typical application: wood, metal (e. g.

nails),plaster board and soft plastics.

When plunging and sawing use a slight

pendulum motion, to allow sufﬁcient chip

removal.

10. SCRAPING

Typical application: Scraping off old varnish or

adhesives, removing glued carpeting,

e. g. on stairs or other small to medium-sized

surfaces.

Select medium/high oscillation frequency (for

variable speed models).

WORKINg HINTS FOR yOuR

TOOL

If your power tool becomes too hot, especially

when used at low speed, set the speed to

maximum and run it with no load for 2-3

minutes to cool the motor. Avoid prolonged

usage at very low speeds. Always keep the

blade sharp.

Always ensure the workpiece is ﬁrmly held or

clamped to prevent movement.

Any movement of the material may affect the

quality of the cutting or sanding ﬁnish.

Start your tool before working and turn it off

only after you stop working.

Do not start sanding without having the

sandpaper ﬁtted.

Do not allow the sandpaper to wear away , it

will damage the sanding pad. The guarantee

does not cover sanding pad wear and tear.

Use coarse grit paper to sand rough surfaces,

medium grit for smooth surfaces and ﬁne grit

for ﬁnishing surfaces. If necessary, ﬁrst make

a test run on scrap material.

Excessive force will reduce the working

efﬁciency and cause motor overload.

Replacing the accessory regularly will

maintain optimum working efﬁciency.

MAINTENANCE

Remove the plug from the socket

before carrying out any adjustment,

servicing or maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no

user serviceable parts in your power tool.

Never use water or chemical cleaners to

clean your power tool. Wipe clean with a

dry cloth. Always store your power tool in a

dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust.

Occasionally you may see sparks through the

ventilation slots. This is normal and will not

damage your power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order

to avoid a hazard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX671.3 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info