Bedienungsanleitung Xerox WorkCentre 3210 (Seite 39 von 140) (Englisch)

610742

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

38 _Loading originals and print media

3. When you print in application, start the print menu.

4. Before you print, open printer properties.

5. Press the Paper tab in printer properties, and select an appropriate

paper type.

6. Select Manual Feeder in paper source then, press OK.

7. Start printing in application.

8. Press the Stop/Clear button on the machine to start feeding

then the machine starts printing.

ADJUSTING THE OUTPUT SUPPORT

The printed pages stack on the output tray, and the output support will help

the printed pages align. To let the output support correctly align the pages

you need to pull it out appropriately depending on the paper size.

Stacking papers firmly

If you use a machine in a humid area, or you are using the damp print media

caused by a high humidity, the print-outs on the output tray may be curled

and may not be stacked properly. In this case, you can set the machine to

use the Paper Stacking function to let print-outs stacked firmly. But, using

this function will make the print speed slow.

1. Press Menu until System Setup appears on the bottom line of the

display and press OK.

2. Press the left/right arrow until Maintenance appears and press OK.

3. Press the left/right arrow until Paper Stacking appears and press OK.

4. Press the left/right arrow to select On or Off and press OK.

5. Press Stop/Clear to return to ready mode.

SETTING THE PAPER SIZE AND TYPE

After loading paper in the paper tray, you need to set the paper size and

type using the control panel buttons. These settings will apply to Copy and

Fax modes. For PC-printing, you need to select the paper size and type in

the application program you use on your PC.

1. Press Menu until System Setup appears on the bottom line of the

display and press OK.

2. Press the left/right arrow until Paper Setup appears and press OK.

3. Press OK when Paper Size appears.

4. Press the left/right arrow until the paper tray you want appears and

press OK.

5. Press the left/right arrow until the paper size you are using appears and

press OK.

6. Press the left/right arrow until Paper Type appears and press OK.

7. Press the left/right arrow until the paper tray you want appears and

press OK.

8. Press the left/right arrow until the paper type you are using appears and

press OK.

9. Press Stop/Clear to return to ready mode.

Place the side to be printed facing up.

Envelope

Preprinted paper Transparency

Punched paper

Card stock Letterhead paper

Label

If you want to use a label, set the paper type to Label.

• If you are printing multiple pages, load the next sheet after first

page prints out, and press the Stop/Clear button. Repeat

this step for every page to be printed.

• The settings you change remain in effect only while you are

using the current application.

1 Output support

• If the output support is incorrectly adjusted, printed pages may be

mis-aligned or fall.

• If you continuously print many pages, the surface of the output tray

may become hot. Be careful not to touch the surface, and

especially keep children away from the surface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Xerox WorkCentre 3210 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Xerox WorkCentre 3210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info