Bedienungsanleitung Xerox WorkCentre 5775 (Seite 297 von 328) (Englisch)

610813

297

Zoom out

Zoom in

Vorherige Seite

1/328

Nächste Seite

Troubleshooting

WorkCentre™ 5735/5740/5745/5755/5765/5775/5790

General Care and Troubleshooting

297

Paper Curls • Load the paper in the paper trays with the seam side of the paper up.

Load the paper in the Bypass Tray with the seam side down.

• Load non-standard media in the Bypass Tray.

• If the paper curls excessively, flip the paper over in the applicable paper

tray.

The Finisher does not stack the

output correctly

• Unload the finisher tray frequently.

• Do not remove stapled sets while the finisher is compiling.

• Check the paper tray guides are locked into position against the paper.

• When using large paper, remove any output contained in the Stacker

Tray.

• Load the paper in the paper trays with the seam side of the paper up.

Load the paper in the Bypass Tray with the seam side down.

• Load non-standard media in the Bypass Tray.

• If the paper curls excessively, flip the paper over in the applicable paper

tray.

• Check the correct paper size has been selected for the paper loaded in

the tray.

The Finisher does not staple or

hole punch correctly

• To correct stapling problems, ensure the maximum number of sheets is

not exceeded for the finisher being used.

• The maximum number of sheets when stapling heavyweight paper is

determined by the finisher type. The Basic Office Finisher staples 12

sheets of heavyweight paper, the Office Finisher staples 20 sheets of

heavyweight paper, and the High Volume Finisher staples 30 sheets.

• Check the correct option has been selected on the touch screen.

• Check the touch screen for a fault message indicating no staples.

Replace the staple cartridge.

• When using large paper, remove any output contained in the Stacker

Tray.

• Check that the hole punch waste container is not full. The hole punch

waste container collects waste from the hole punch.

• Check the correct paper size has been selected for the paper loaded in

the tray.

• Check the paper tray guides are locked into position against the paper.

Stray marks or black marks

from hole punched originals are

not removed

•Use the Edge Erase option to erase the edge with the punched holes.

Refer to Edge Erase on page 54 of Copy.

• Copy from the document glass with the document cover or document

feeder down.

Images are out of sequence or

upside down when the Booklet

Creation feature is used

• Ensure that the originals are in the correct sequence.

• Feed LEF originals to SEF orientated paper.

• Enable the display options for Booklet Creation and ensure that the

correct sequence is selected (i.e. Left to Right or Right to Left).

The output is blank • Ensure the originals are loaded either face up in the document feeder or

face down on the document glass in the top right position.

Problem Potential Solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Xerox WorkCentre 5775 Seite 297

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Xerox WorkCentre 5775

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info