Bedienungsanleitung Xiaomi Roborock Robot Vacuum Cleaner (Seite 6 von 13) (Englisch)

730175

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Using

Partial cleaning

When the device is in the standby mode or paused, press the button for partial cleaning,

after which the device will remove the central area of the room with a size

of 1.5x1.5 m. When the device nishes its work, it will automatically return to its original

position, completing the cleaning of a certain zone.

Attention: if the device is paused, pressing the partial cleaning button stops cleaning the

previous zone.

Pause

While the device is operating, press any button on the vacuum cleaner to stop it.

Press the Power / Cleaning button to continue cleaning;

Press the Charging button to bring the vacuum cleaner back to the docking station for

recharging and stop the current cleaning.

Attention: if the device is paused, you turn on the function of returning to the docking

station, the current cleaning of the premises is over.

If cleaning is necessary, add water or rinse the wet cleaning attachment, rst press any

button to pause the device, then remove the wet cleaning module from the vacuum

cleaner, add water or rinse an attachment. After this, install the module for wet cleaning

back and press the Power / Clean button to continue cleaning.

Troubleshooting

If a malfunction occurs during the cleaning process, the ring-shaped indicator of the device

will ash rapidly in red and the voice message will turn on. To solve this problem, see the

«Troubleshooting» section.

Attention:

- If the device does not work for 10 minutes due to a problem, it automatically enters sleep

mode.

- If a malfunction occurs during charging on the dock, the device stops pre-cleaning.

Sleep mode

If the device does not perform any actions within 10 minutes, it can automatically switch to

sleep mode. In this case, the ring-shaped indicator ashes once every few seconds.

To awaken the device, press any button on the vacuum cleaner.

Attention:

- The device does not enter sleep mode if it is on recharging

on the docking station.

- If the device is in sleep mode for more than 12 hours, it automatically turns o.

Setting cleaning time

Thanks to the mobile application, you can set the cleaning time of the room. In this case,

the vacuum cleaner automatically starts to clean at the set time, and after the cleaning is

completed, it automatically returns to the docking station.

Reset Wi-Fi settings

If you replace the router, forget the password, or if there are any other situations, that

caused a problem with connecting the device to the mobile application, open the top panel

of the vacuum cleaner to see the Wi-Fi indicator, simultaneously press and hold the Partial

cleaning and Charging buttons, You will hear a voice alert when you reset your Wi-Fi

settings. Wait until the Wi-Fi indicator starts ashing slowly, indicating a successful reset.

Setting cleaning zone

Using the mobile application, set the cleaning zone, after which the vacuum cleaner will

clean only the zone, dened by you.

Setting the end point

Using the mobile application, set the desired point on the map of the room, the device will

automatically determine the route to achieve the goal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Xiaomi Roborock Robot Vacuum Cleaner Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info