Bedienungsanleitung Xoro HSD 8550 (Seite 60 von 142) (Deutsch, Englisch)

497010

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

14 HSD 8550

English

Connection

Connecting with a YUV (Y Pb Pr) cable

YUV (Y Pb Pr) is a transmission technology separating colour and brightness information in the

signal. Similar to RGB, the signals are transmitted on a 3 wire cinch [RCA] cable. This way of

transmission is also called “component”. This connection offers best picture quality available with

analogue signal transmission.

Plug a cable into the Y Pb Pr socket on the rear side of your DVD player. You can recognize the

sockets by their colours red, green and blue easily. The other side of the cable must be connected

to the Y Pb Pr input socket of the TV-set (usually labelled „Y Pb Pr“ or „HDTV IN“.

Please change the video output in the Setup settings to “YUV

”. In case, that your TV set supports

progressive Scan, you can choose by the settings “Resolution

” by the option “Video Settings”.

Please uses a resolution of 576p or 720p and than the player transmit a progressive signal to the

TV set.

As YUV does not transmit sound, you also must add an audio connection. Insert one end of the

supplied audio (Cinch [RCA]) cable into the white/red Cinch [RCA] socket L/R AUDIO OUT at the

back of the DVD player and the other end into the audio input socket (usually white/red) on the TV

set (usually labelled “AUDIO IN” or “AV IN”. Please also refer to your TV set’s user manual). Switch

on the TV set and select the YUV input or the respective channel number. For channel number and

input selection please also refer to your TV operating instructions.

Note:

Make sure you observe the colours of the three sockets when you establish the connection. When

the colours are connected in a wrong way, no picture or a picture with wrong colours will be

displayed.

Connecting with a HDMI Cable

HDMI is a digital transmission technology for both audio and video. Connect the DVD player and

display with a HDMI-HDMI cable. Please note that some TV set can not support RAW audio. In this

case, please set the DVD player audio digital output to PCM.

If your TV set is not equipped with HDMI, but with DVI input, you can use a conversion cable or an

adapter to DVI.

As DVI does not transmit sound, you also must add an audio connection. Insert one end of an audio

(Cinch [RCA]) cable into the white/red Cinch [RCA] socket ML/MR AUDIO OUT at the back of the

DVD player and the other end into the audio input socket (usually white/red) on the TV set (usually

labelled “AUDIO IN” or “AV IN”. Please also refer to your TV set’s user manual)

You can choose in the settings “Resolution

” by the option “System Settings” the resolution which

you want or which the TV set supports.

Switch on the TV set and select the HDMI or DVI input. For input selection please also refer to your

TV operating instructions.

Video Output

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Xoro HSD 8550 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info