Bedienungsanleitung Yale SR330 (Seite 15 von 20) (Englisch)

655219

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Low Battery Indication

The App will display the low battery message under the

actual device.

When a device rst shows the low battery signal it has

enough battery capacity to operate for a further month

before complete exhaustion.

Door/Window Contact Battery Change

When the battery is low the LED will light up when the

door/window is opened. The battery is changed as follows:

1. Ensure the system is disarmed.

2. Loosen the case screw and remove the Door/Window

Contact from the base to reveal battery.

3. Using a screwdriver gently lever out the old battery.

4. Insert new CR2032 coin cell battery with the + side

uppermost. See picture on page 16.

5. Press battery into holder rmly with nger and thumb

until a click is heard.

6. Ret sensor on base and tighten bottom case screw.

Switch tamper protection back on.

• Door/Window Contact case tamper conditions are also

indicated by a lit LED, check the tamper before changing

the battery.

PIR Motion Detector & Image / Video Camera

Battery Change

When the battery is low the LED will ash when any motion

is detected. The batteries are changed as follows:

1. Ensure the system is disarmed.

2. Loosen the case screw and remove PIR from base to

reveal the batteries.

3. Insert new batteries observing correct polarity. (Note:

PIR Motion Detector takes 3x AAA alkaline batteries, PIR

Image Camera takes 2x AA alkaline batteries and PIR

Video Camera takes 3 x AA Lithium batteries. The PIR

LED will ash for 30 seconds while initialising.

4. Ret PIR on base and tighten bottom case screw.

• Ensure tamper spring is fully depressed when re-tting

the PIR to the back case. If this has not been done

correctly this will be indicated by a ashing LED on the

PIR.

External Siren Battery Change

When the batteries start getting low the Siren will produce

a series of audible pips and ashes during arming and

disarming.

1. Ensure the system is disarmed. Select “Controller”,

Device List”, click Siren’s Properties (icon on the right)

and set Siren Bypass to the OFF position.

2. Remove the Siren lid and switch the Siren power switch

to OFF.

3. Unscrew the four screws on the battery compartment lid

and remove the cover.

4. Remove the four batteries, wait for 30 seconds, and

replace them with four fresh alkaline “D” batteries.

5. Switch on Siren power and check that the Siren beeps

and ashes.

Warning: After the batteries have been inserted, the

tamper will become active after three hours. Please replace

the cover back onto the Siren quickly.

• Siren case tamper conditions are also signalled by a

series of beeps when the system is armed but not when

the system is disarmed (low battery warning produces a

series of audible pips when armed and disarmed), take

care not to confuse the two dierent conditions.

Changing the Batteries

Always use correct type of batteries as replacements because any other battery can

cause problems with the operation of the system. Ensure the correct steps are taken

when changing batteries in tamper protected devices.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yale SR330 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info