Bedienungsanleitung Yale SR330 (Seite 17 von 20) (Englisch)

655219

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Troubleshooting

External Siren

Siren produces a 3 second alarm

when disarmed

• There has been a previous alarm and there might be an

intruder still in the premises.

Siren produces a series of audible pips when

armed or disarmed

• If the Siren produces a series of pips when arming and

disarming this indicates low batteries.

• If the Siren produces a series of pips only when arming this

indicates a tamper fault. Check that the Siren cover is rmly

secured and the tamper spring on the back of the Siren

is fully depressed when in contact with the wall. If not use

suitable packing material to ll the gap (refer to page 9 for

diagram).

Siren produces an interrupted tone when sounding

an alarm

• The Siren has low batteries. Change batteries with new

alkaline replacements (see page 15).

External Siren

Siren does not respond to Arming or Disarming

• Siren batteries are completely exhausted. See instructions

for changing batteries on page 15.

• Siren not learnt-in. If Siren produces a tamper alarm when

the cover is removed and Siren is OK, learn-in the Siren (see

page 7).

• Siren is not in range of the Smart Hub.

If you experience a problem with adding the

External Siren to you Alarm system

• Ensure the dip switch positions are as shown in the diagram.

If the switches are in the wrong position, please change

accordingly

• After changing the dip switch, turn o the power for 30

seconds, then turn the power on again for the changes to

take eect.

Door/Window Contact

Door/Window Contact LED lights up

• Batteries are low or the tamper switch has been disturbed.

Check that the tamper switch spring is making contact with

the mounting surface. If the tamper switch is OK, please

change the battery (see page 15).

Door/Window Contact does not respond to opening

when jumper is in the test position

• Batteries are completely exhausted. Change battery

(see page 15).

• The magnet is too far away from the Door/Window Contact.

Check that the gap between the Door/Window Contact and

magnet is not greater than 10mm.

PIR Motion Detector

PIR does not respond to motion

• Previous motion has triggered the PIR sleep timer and is

preventing subsequent motion detection. Arm the system

and vacate protected area for at least 90 seconds before

testing. By pressing the learn/test button the PIR LED will

light up and detect motion for the rst minute.

PIR Motion Detector is slow to respond

• This is normal, the PIR Motion Detector has sophisticated

false alarm ltering that will lter out random uctuations and

responds to genuine motion across eld of view, it is less

sensitive walking directly towards it.

PIR Motion Detector gives false alarms

• Check pets have no access to the protected area.

• Check that the PIR Motion Detector is not pointed at sources

of heat or moving objects, e.g. uttering curtains.

• Check that the PIR Motion Detector is not mounted above

convector heaters or pointing directly at windows.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yale SR330 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info