Bedienungsanleitung Yamaha 01V (Seite 287 von 308) (Deutsch)

517044

287

Zoom out

Zoom in

Vorherige Seite

1/308

Nächste Seite

286 MIDI-Datenformat

01V—Bedienungsanleitung

MIDI-Datenformat

1. TRANSMIT/RECEIVE DATA

1.1 CHANNEL MESSAGE

1.1.1 NOTE OFF (8n)

Reception

Received if [Rx CH] matches.

Used for EFFECT control. See below for details.

1.1.2 NOTE ON (9n)

Reception

Received if [Rx CH] matches.

Used for EFFECT control. See below for details.

A velocity of 0x00 is the same as NOTE OFF.

* Using Note data for EFFECT control

1: Dynamic Flange/Dynamic Phase/Dynamic Filter

When the SOURCE parameter is set to MIDI, Velocity will be used

together with Note On/Off to control the frequency width of Modu-

lation.

2: Freeze

When PLAY MODE is MOMENT or CONTINUE, a Note On mes-

sage will start play. However, this is only when the note number spec-

iﬁed for MIDI TRG is received. Also, play will not occur if there is no

recorded data.

Regardless of the Note Number, a Note Off message will stop play if

PLAY MODE is MOMENT.

1.1.3 CONTROL CHANGE (Bn)

Reception

Received when [Control Change RX] is ON and the [Rx CH]

matches. However if [OMNI] is ON, this message is received regard-

less of the channel.

When [Control Change ECHO] is ON, this message will be echoed.

Parameters will be controlled according to the settings of the [control

assign table].

Control of speciﬁc faders can be disabled by the [midi fader control

input mute] settings.

If this message is received while the [control assign table] page is dis-

played, the cursor location will move to that control number.

Transmission

If [Control Change TX] is ON, this message is transmitted on the [Tx

CH] whenever a parameter speciﬁed in the [control assign table] is

operated.

If [Control Change ECHO] is ON, these messages will be merged

with the unit's own output while taking advantage of running status.

The control value is converted to the parameter value according to

the following equation.

C = 128 (byte parameter)

16384 (word parameter)

S = number of total possible steps for the parameter

C / S = X remainder Y

INT((Y+1)/2) = Z

If (MIDI DATA - Z) < 0 then -> param = 0

If ((MIDI DATA - Z)/X) > MAX then -> param = MAX

In other cases -> param =

INT((MIDI DATA -Z)/X)

1.1.4 PROGRAM CHANGE (Cn)

Reception

Received when [Program Change RX] is ON if the [Rx CH] matches.

However if [OMNI] is ON, this is received regardless of the channel.

This is echoed if [Program Change ECHO] is ON.

A scene memory will be recalled according to the settings of the [Pro-

gram change table].

Transmission

If [Program Change TX] is ON, this is transmitted on the [Tx CH]

channel when a scene memory is recalled.

If two or more program numbers have been assigned to the memory

number which was recalled, the lowest numbered program number

will be transmitted.

This message is echoed if [Program Change ECHO] is ON. (If a

memory number which is not speciﬁed in the [Midi Program

Change Assign Table] is recalled, the Parameter Change (Function

Call) described below will be transmitted.)

1.2 EXCLUSIVE MESSAGE (F0-F7)

1.2.1 MOTION CONTROL STATE (MCS)

MMC STOP/PLAY/FORWARD/REWIND/RECORD/

PAUSE

Transmission

In the [REMOTE-MMC] page, this is transmitted by key operations.

The [DEVICE NO.] speciﬁes the transmission destination.

1.2.2 MOTION CONTROL PROCESS (MCP)

MMC LOCATE (target)

Transmission

In the [REMOTE-MMC] page, this is transmitted by key operations.

The [DEVICE NO.] speciﬁes the transmission destination. (The ID

of the receiving device must be set.)

STATUS 1000nnnn 8n Note Off Message

DATA 0nnnnnnn nn Note No.

0vvvvvvv vv Velocity ( ignored)

STATUS 1001nnnn 9n Note On Message

DATA 0nnnnnnn nn Note No.

0vvvvvvv vv Velocity ( 1-127:On, 0:off)

STATUS 1011nnnn Bn Control Change

DATA 0ccccccc cc Control No. ( 0-95, 102-119)

0vvvvvvv vv Control Value (0-127)

STATUS 1100nnnn Cn Program Change

DATA 0nnnnnnn nn Program No. ( 0-127)

STATUS 11110000 F0 System Exclusive Message

ID No. 01111111 7F Real Time System Exclusive

Device ID 0ddddddd dd Destination (00-7E, 7F:all call)

Command 00000110 06 Machine Control Command(mcc) sub-id

0ccccccc cc Command String

[1]:Stop

[2]:Play

[4]:Fast Forward

[5]:Rewind

[6]:Record Strobe

[9]:Pause

EOX 11110111 F7 End Of Exclusive

STATUS 11110000 F0 System Exclusive Message

ID No. 01111111 7F Real Time System Exclusive

Device ID 0ddddddd dd Destination (00-7E, 7F:all call)

Command 00000110 06 Machine Control Command(mcc) sub-id

01000100 44 Locate

00000110 06 byte count

00000001 01 "target" sub command

0hhhhhhh hh hour

0mmmmmmm mm minute

0sssssss ss second

0fffffff ff frame

0sssssss ss sub-frame( only '0')

EOX 11110111 F7 End Of Exclusive

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 01V Seite 287

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 01V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info