Bedienungsanleitung Yamaha 01V (Seite 292 von 308) (Deutsch)

517044

292

Zoom out

Zoom in

Vorherige Seite

1/308

Nächste Seite

MIDI-Datenformat 291

01V—Bedienungsanleitung

PARAMETER CHANGE(type 0x05:remote meter)

When the following request is received to enable transmission, the

speciﬁed parameter data will be transmitted at 30 msec intervals for

ﬁve seconds. If you want meter data to be transmitted continuously,

you must continue transmitting requests less than ﬁve seconds apart.

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the

Device Channel that is included in the SUB STATUS, this message is

received.

When [LOCAL OFF] is ON, the incoming meter data will be dis-

played. In other cases it will be ignored.

Transmission

When transmission is enabled by a request, this will be transmitted

every 30msec on the [Rx CH] channel, for ﬁve seconds.

Transmission will be disabled when the power is turned on, and when

PORT settings have been modiﬁed.

In the Meter no., bit 6 is the special bit, and bit 5 is the gr bit.

When the Gr bit is on, the single byte gr will be added uniformly to

the end of the data string.

When the Special bit is on, the two bytes stLED L/R will be added uni-

formly to the end of the data string.

When both are on, gr comes ﬁrst, and stLED L/R come later.

PARAMETER VALUE REQUEST(type 0x05:remote

meter)

This message is used to obtain meter data from the 01V. It is used in

LOCAL OFF MODE to display the meter of the remote device, or to

display the meter on the screen of a personal computer, etc.

In order to obtain meter data, the meter whose data is required must

be displayed in the LCD of the remote device. This means that before

transmitting this request, you must ﬁrst transmit the

above-described "4.6.4.11 PARAMETER CHANGE (type 0x03:bit

operation for controller(LCD-Fader mode))" to display the appro-

priate meter in the LCD screen of the remote device.

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the

Device Channel included in SUB STATUS, this message will be

received.

When this message is received, Parameter Change (remote meter)

messages will begin to be transmitted on the [Rx CH] channel.

Transmission

When [LOCAL OFF] is ON, transmit a meter data request for the

currently displayed meter on the [Tx CH]. For each request, meter

data will be transmitted for ﬁve seconds. If you want meter data con-

tinuously for longer than this, you will need to transmit requests at

intervals of ﬁve seconds or less. When the 01V is in LOCAL OFF

MODE, transmit requests at approximately one-second intervals.

When [Parameter Change ECHO] is ON and the 01V itself did not

receive this message, the message will be echoed.

Table of signal levels and codes

5. SYSTEM EXCLUSIVE

MESSAGE (Bulk Dump) &

REQUEST

These messages input and output the contents of various types of

internal memory.

The unique header identiﬁes whether or not the data is for the 01V.

The CHECK SUM is calculated by adding the data following the

BYTE COUNT(LOW) until the data preceding the CHECK SUM,

then inverting the bits (2's complement), and setting bit 7 to 0.

CHECK SUM = ( -sum) & 0x7F

Reception

This is received if [Bulk RX] is ON and the [Rx CH] matches the

Device Channel that is included in SUB STATUS.

When a BULK DUMP is received, it will immediately be written into

the speciﬁed memory.

When a BULK DUMP REQUEST is received, a bulk dump will be

transmitted immediately.

Transmission

In the [MIDI-BULK] page, this is transmitted on the [Tx CH] chan-

nel by key operations.

In response to a Bulk Dump Request, a Bulk Dump Message is trans-

mitted on the [Rx CH] channel.

STATUS 11110000 F0 System Exclusive Message

ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)

SUB STATUS 0001nnnn 1n n=0-15(Tx/Rx Channel No.1-16)

GROUOP ID 00111110 3e MODEL ID

MODEL ID 00000100 04 Device code (01V)

PARAM TYPE 00000101 05 remote meter

DATA 0sgttttt tt meter no.(s:special bit, g:gr bit)

0mmmmmmm mm0

0mmmmmmm mm1

: :

EOX 11110111 F7 End Of Exclusive

STATUS 11110000 F0 System Exclusive Message

ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)

SUB STATUS 0011nnnn 3n n=0-15(Tx/Rx Channel No.1-16)

GROUOP ID 00111110 3e MODEL ID

MODEL ID 00000100 04 Device code (01V)

PARAM TYPE 00000101 05 remote meter

DATA 0sgttttt tt meter no.(s:special bit, g:gr bit)

EOX 11110111 F7 End Of Exclusive

Level code Level code Level code

------------------------------------------------------------------------------------

-72dB 0x1F -30dB 0x57 -9dB 0x72

-68dB 0x24 -27dB 0x5A -8dB 0x73

-64dB 0x29 -24dB 0x5F -7dB 0x75

-60dB 0x2F -21dB 0x62 -6dB 0x77

-56dB 0x33 -18dB 0x67 -5dB 0x78

-51dB 0x3A -16dB 0x69 -4dB 0x79

-48dB 0x3F -15dB 0x6A -3dB 0x7A

-46dB 0x41 -14dB 0x6B -2dB 0x7B

-42dB 0x47 -13dB 0x6D -1dB 0x7D

-39dB 0x4A -12dB 0x6F 0dB 0x7E

-36dB 0x4F -11dB 0x70 CLIP 0x7F

-33dB 0x52 -10dB 0x71

data name rx/tx function

------------------------------------------------------------------------------------------------------

'M' rx/tx Scene Memory & Request

'S' rx/tx Setup Memory & Request

'I' rx/tx Remote(Internal Parameter) Memory & Request

'L' rx/tx Remote(MMC) Memory & Request

'U' rx/tx Remote(User Deﬁne) Memory & Request

'C' rx/tx Control Change Assign Table & Request

'P' rx/tx Program Change Assign Table & Request

'Q' rx/tx Equalizer Library & Request

'Y' rx/tx Dynamics Library & Request

'E' rx/tx Effect Library & Request

Yamaha 01V Seite 292

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 01V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info