Bedienungsanleitung Yamaha 01V (Seite 291 von 308) (Deutsch)

517044

291

Zoom out

Zoom in

Vorherige Seite

1/308

Nächste Seite

290 MIDI-Datenformat

01V—Bedienungsanleitung

PARAMETER CHANGE (type operation for type

0x03:controller(LCD-Fader mode))

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the

Device Channel included in the SUB STATUS, the message will be

received.

When [Parameter Change ECHO] is ON, this message will be ech-

oed.

When this message is received, the LCD screen, the corresponding

Fader Mode, and the speciﬁed channel will be selected.

PARAMETER CHANGE (bit operation for type

0x43:controller(key remote))

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the

Device Channel included in the SUB STATUS, this message will be

received.

When [Parameter Change ECHO] is ON, this message will be ech-

oed.

When this message is received, the same processing will be performed

as when the speciﬁed key (refer to the table below) is pressed

(released).

Transmission

When [Parameter Change ECHO] is ON, this message will be trans-

mitted without change.

* Normally, data should be transmitted as "set(bit3=1)." In this case,

the 01V will determine that that switch has been pressed and then

immediately released, and will perform the appropriate processing.

This means that you will not have to transmit "reset(bit3=0)" sepa-

rately.

* The keys followed by 100 are virtual key, it would be the keys on

LCD.

PARAMETER CHANGE (type 0x04:multiple linking)

This message is valid only for the connector that has been speciﬁed as

the LINK PORT.

When two '01V' units have been connected by a cable, some of the

functions (refer to the following table) will be linked.

The same LINK PORT connector settings must be made on both

units.

Reception

This message is always received, and will execute the LINK function

(refer to the following table). (This is not dependent on

MIDI-SETUP.)

Transmission

This message is transmitted when LINK-related functions (refer to

following table) are performed. (This is not dependent on

MIDI-SETUP.)

When [Parameter Change ECHO] is ON, this message is transmitted

without change.

STATUS 11110000 F0 System Exclusive Message

ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)

SUB STATUS 0001nnnn 1n parameter change n=0-15(Device Chan-

nel No.1-16)

GROUOP ID 00111110 3e MODEL ID

MODEL ID 00000100 04 Device code (01V)

PARAM TYPE 01000011 03 controller (type)

DATA 00000001 01 control No.(LCD-Fader mode)

0ddddddd dd channel select(0-30)

0ddddddd dd LCD select No.(0-17)

0000dddd dd PAGE No.(0-4)

EOX 11110111 F7 End Of Exclusive

STATUS 11110000 F0 System Exclusive Message

ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)

SUB STATUS 0001nnnn 1n parameter change n=0-15(Device Chan-

nel No.1-16)

GROUOP ID 00111110 3e MODEL ID

MODEL ID 00000100 04 Device code (01V)

PARAM TYPE 01000011 43 controller

DATA 00000000 00 control no.(0:key remote)

0ddddddd dd No. 0-10,99-102(key 1-11,100-103)

0000dddd dd data(bit0-2:change bit no.0-7, bit3:0=reset

1=set)

: :

EOX 11110111 F7 End Of Exclusive

KEY key no.bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7

-------------------------------------------------------------------------------------------------------------------------------------------------

key1 0 ON1 ON2 ON3 ON4 ON5 ON6 ON7 ON8

key2 1 ON9 ON10 ON11 ON12 ON13-14 ON15-16 ONSTOUT ------

key3 2 SOLO1 SOLO2 SOLO3 SOLO4 SOLO5 SOLO6 SOLO7 SOLO8

key4 3 SOLO9 SOLO10 SOLO11 SOLO12 SOLO13-14SOLO15-16 ------ ------

key5 4 SEL1 SEL2 SEL3 SEL4 SEL5 SEL6 SEL7 SEL8

key6 5 SEL9 SEL10 SEL11 SEL12 SEL13-14 SEL15-16 SEL STO ------

key7 6 ONRTN1 ONRTN2 SOLORT1 SOLORT2 SELRTN1 SELRTN2 HOME MEMORY

key8 7 AUX1 AUX2 AUX3 AUX4 EFFECT1 EFFECT2 OPTION REMOTE

key9 8 LOW L-MID H-MID HIGH ------ ------ ------ ------

key10 9 UP LEFT RIGHT DOWN ENTER INC DEC ------

key11 10 DYNAMIX EQ DELAY PAN UTILITY MIDI SETUP VIEW

key100 99 FRZ-REC FRZ-PLAY ------ ------ ------ ------ ------ ------

key101 100 SOLO1 SOLO2 SOLO3 SOLO4 SOLO5 SOLO6 SOLO7 SOLO8

key102 101 SOLO9 SOLO10 SOLO11 SOLO12 SOLO13-14SOLO15-16 SOLO-RTN1SOLO-RTN2

key103 102 SOLO17 SOLO18 SOLO19 SOLO20 SOLO21 SOLO22 SOLO23 SOLO24

STATUS 11110000 F0 System Exclusive Message

ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)

SUB STATUS 0001nnnn 1n n=0-15(Tx/Rx Channel No.1-16)

GROUOP ID 00111110 3e MODEL ID

MODEL ID 00000100 04 Device code (01V)

PARAM TYPE 00000100 04 multiple linking

DATA 0mmfffff mf data format (bit6-5:status, bit4-0:contents)

0ddddddd dd0 data #0

0ddddddd dd1 data #1

: :

EOX 11110111 F7 End Of Exclusive

Status Function Note

----------------------------------------------------------------------------------------------------------

0x00 scene recall Recall the speciﬁed memory number

0x01 scene store Store to the speciﬁed memory number with title

(Assign the same title to all)

0x02 scene title edit If the title was modiﬁed, make it the same, make it

match

0x48 solo mode Match the solo mode

bit6: enable/disable

bit5: on/off

bit2: recording/mixdown

bit1: sel mix/last

bit0: after fader/pre fader

0x60 display call When the screen (Fader Mode) is changed, make it

match

0x61 metering point Make the meter points match

0x62 peak hold Make the meter Peak Hold ON/OFF match

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 01V Seite 291

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 01V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info