Bedienungsanleitung Yamaha 01V96i (Seite 28 von 71) (Englisch)

517047

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

28 Connections and Setup

01V96i—Owner’s Manual

Specifying the Wordclock

Source

To digitally connect the 01V96i to external devices, you

must specify the wordclock source for the system. Fol-

low the steps below.

1. Press the DISPLAY ACCESS [DIO/SETUP]

button repeatedly until the DIO/Setup |

Word Clock page appears.

On this page, you can view the current synchroni-

zation status of input signals at each slot and con-

nector.

The source select button indicators are explained

below:

A usable wordclock signal is present at this

input, and it is in sync with the current 01V96i

internal clock.

No wordclock signal is present at this input.

A usable wordclock signal is present at this

input, but it is out of sync with the current

01V96i internal clock.

This input is the currently-selected wordclock

source.

This input was selected as the wordclock

source, but no usable signal was received.

Either this input is not receiving wordclock, or

else it cannot be used with the cur-

rently-installed I/O card.

2. Use the cursor buttons to move the cur-

sor to a source, then press [ENTER].

The following are possible wordclock sources.

However, USB only displays the synchronization

status, and cannot be selected as the wordclock

master.

•SLOT

These buttons select the inputs from the digital I/O

card installed in the slot as the wordclock source.

Inputs are selected in pairs (odd and even numbers

in this order). The SLOT TYPE column displays the

names of any installed I/O card. The number of

pairs depends on the type of I/O card installed.

•adat

These buttons select the inputs from the ADAT IN

connector on the rear panel. Inputs are selected in

pairs (odd and even numbers in this order).

•WC IN

This button selects the wordclock signal input at the

WORD CLOCK IN connector on the rear panel.

•2TRD

This button selects the 2TR IN DIGITAL input as

the wordclock source.

• INT 44.1k, INT 48k, INT 88.2k, INT 96k

These buttons select the internal clock generator as

the wordclock source. The 01V96i will function as

the wordclock master.

•USB (display only)

This indicates the synchronization status of the sig-

nal being input from the TO HOST USB port. It

cannot be selected as the wordclock master.

Note: When you change the wordclock settings on any

device in your digital audio system, some devices may out-

put noise due to being out of synchronization. Be sure to

turn down your monitoring device before changing word-

clock settings.

Tip:

• The FS box displays the sampling frequency at which the

01V96i is currently operating.

• The SLOT TYPE column displays the names of any

installed I/O card.

• The IN and OUT columns indicate the number of input

and output channels available for each installed I/O

card.

Note: To transfer data at higher sampling frequencies

(88.2 kHz or 96 kHz) between the 01V96i and connected

external devices, you need to set the data transfer format.

Tip: If wordclock transfer is interrupted while the 01V96i

(being used as a slave unit) is receiving the clock signal, the

unit will automatically switch to an internal clock (INT

44.1k/ INT 48k/INT 88.2k/INT 96k) that is closest to the

interrupted clock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 01V96i Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 01V96i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info