Bedienungsanleitung Yamaha 02R96 (Seite 293 von 317) (Deutsch, Englisch)

517056

293

Zoom out

Zoom in

Vorherige Seite

1/317

Nächste Seite

280 Anhang C: MIDI

02R96—Bedienungsanleitung

If [TABLE] is selected

If [NRPN] is selected

*1) There is no particular need to add the 2nd, 3rd, and 4th status

for transmission. However if these are present during recep-

tion, they should be received.

*2) Does not need to be transmitted if the parameter data fits

within 7 bits.

4. PROGRAM CHANGE (Cn)

Reception

This message is received if [Program Change RX] is ON and [Rx CH]

matches. However if [OMNI] is ON, this is received regardless of the chan-

nel.

A scene memory will be recalled according to the settings of the [Program

Change Table].

This message will be echoed if [Program Change ECHO] is ON.

Transmission

If [Program Change TX] is ON, this message is transmitted according to

the settings of the [Program Change Table] on the [Tx CH] channel when

a scene memory is recalled.

If the recalled scene has been assigned to more than one program number,

the lowest-numbered program number will be transmitted. Transmission

to Studio Manager using Program Change messages will not be performed

since there is no guarantee that the contents of the tables will match. (Pa-

rameter Changes will always be used.)

5. SONG POSITION POINTER (F2)

Reception

If this is received when the automix TIME REFERENCE setting is MIDI

CLOCK, the automix will move to the song position that was received.

6. TIMING CLOCK (F8)

Reception

If the automix TIME REFERENCE setting is MIDI CLOCK, this message

is used to synchronize automix. It is also used to control effects. This mes-

sage is transmitted 24 times per quarter note.

7. START (FA)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI

CLOCK, and will start the automix. In actuality, automix will start when

the next TIMING CLOCK is received after receiving the START message.

8. CONTINUE (FB)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI

CLOCK, and will cause automix to start from the current song position. In

actuality, automix will start when the next TIMING CLOCK is received af-

ter receiving the CONTINUE message.

9. STOP (FC)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI

CLOCK, and will cause automix to stop.

10. ACTIVE SENSING (FE)

Reception

Once this message has been received, the failure to receive any message for

an interval of 400 ms or longer will cause MIDI transmission to be initial-

ized, such as by clearing the Running Status.

11. SYSTEM RESET (FF)

Reception

When this message is received, MIDI communications will be cleared, e.g.,

by clearing the Running Status.

12. SYSTEM EXCLUSIVE MESSAGE (F0)

12.1 MIDI MACHINE CONTROL (MMC)

These messages are transmitted when the Machine Control section of the

02R96 is operated. For details, refer to the MMC specification.

12.2 BULK DUMP

This message sends or receives the contents of various memories stored

within the 02R96.

The basic format is as follows.

For DUMP DATA

For DUMP REQUEST

A unique header (Model ID) is used to determine whether the device is a

02R96.

CHECK SUM is obtained by adding the bytes that follow BYTE COUNT

(LOW) and end before CHECK SUM, taking the binary compliment of

this sum, and then setting bit 7 to 0.

Reception

This message is received if [Bulk RX] is ON and the [Rx CH] matches the

device number included in the SUB STATUS.

When a bulk dump is received, it is immediately written into the specified

memory.

When a bulk dump request is received, a bulk dump is immediately trans-

mitted.

Transmission

This message is transmitted on the [Tx CH] by key operations in the [MI-

DI]-[BULK DUMP] screen.

A bulk dump is transmitted on the [Rx CH] in response to a bulk dump

STATUS 1011nnnn Bn

Control change

DATA 0ccccccc cc

Control number (0-95, 102-119)

0vvvvvvv vv

Control value (0-127)

STATUS 1011nnnn Bn

Control change

DATA 01100010 62

NRPN LSB

0vvvvvvv vv

LSB of parameter number

STATUS 1011nnnn Bn

Control change *1

DATA 01100011 63

NRPN MSB

0vvvvvvv vv

MSB of parameter number

STATUS 1011nnnn Bn

Control change *1

DATA 00100110 26

LSB of data entry

0vvvvvvv vv

LSB of parameter data

STATUS 1011nnnn Bn

Control change *1, *2

DATA 00000110 06

MSB of data entry *2

0vvvvvvv vv

MSB of parameter data *2

STATUS 1100nnnn Cn

Program change

DATA 0nnnnnnn nn

Program number (0-127)

STATUS 11110010 F2

Song position pointer

DATA 0vvvvvvv vv

Song position LSB

0vvvvvvv vv

Song position MSB

STATUS 11111000 F8

Timing clock

STATUS 11111010 FA

Start

STATUS 11111011 FB

Continue

STATUS 11111100 FC

Stop

STATUS 11111101 FE

Active sensing

STATUS 11111111 FF

System reset

F0 43 0n 7E cc cc <Model ID> tt mm mm [Data ...]

cs F7

F0 43 2n 7E <Model ID> tt mm mm F7

Device Number

cc cc

DATA COUNT (the number of bytes that follow this, ending

before the checksum)

Model ID (for the 02R96, this is 4C 4D 20 20 38 43 35 34)

DATA TYPE

mm mm

DATA NUMBER

CHECK SUM

CHECK SUM = (-sum)&0x7F

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 02R96 Seite 293

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 02R96

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info