517061
23
Zoom out
Zoom in
Vorherige Seite
1/89
Nächste Seite
18 02R Applications
Yamaha 02R & 03D Applications Guide
4
02R with ADAT & BRC
This application shows how the 02R can be used with an Alesis ADAT and BRC Master
Remote Control to create a 24-input, 8-track digital recording system. The eight digital tape
returns and 24 Mic/Line inputs provide up to 32 inputs at mixdown. In addition, the 02Rs
built-in automation and scene memory systems provide both dynamic and static mix
automation referenced to timecode.
Connections
The ADAT (CD8-AT) card must be screwed securely in place. Do not leave the screws out
after installation as the card will not be grounded correctly.
The Digital In/Out connectors on the 02R and ADAT are connected together using
Optical Cables. Press the DIGITAL IN button on the ADAT to use the DIGITAL IN.
The ADAT’s eight tracks connect to 02R slot [1], tape inputs one through eight.
The Alesis BRC Master Remote Control can control up to 16 ADATs (i.e. 128 tracks).
A 9-pin sync cable for connecting the ADAT and BRC is available from Alesis.
The BRC provides ADAT timecode to SMPTE timecode conversion. In addition, a
timecode offset can be specified, so the automix start time can be adjusted.
The 75 ohm wordclock termination switch on the back of the 02R is set to ON.
02R Wordclock Setup
On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.
ADAT & BRC Wordclock Setup
The BRC works as wordclock master and the ADAT locks to it automatically via the 9-pin
sync cable. The sampling rate can be set to either 48 kHz or 44.1 kHz. Use Fixed mode for
48 kHz and Variable mode for 44.1 kHz (using the PITCH DOWN button, set to –147 cents.
At which point “–146, 44.1, –148” appears on the display). The newer ADAT-XT has
dedicated switches for selecting these two sampling rates.
Notes
Press the DIGITAL IN button on the ADAT to use the DIGITAL INPUT.
The ADAT must be powered up before the BRC, because when the BRC is powered up it
checks how many ADATs are connected, allocates them device numbers, and
automatically sets the system wordclock.
To generate timecode on the BRC, press the GEN SYNC button.
On the BRC, set the DIGITAL I/O button to OFF. This function is for direct ping-pong
between multiple ADATs. If this is turned ON while connected to an 02R, bus
assignments will produce unexpected results. Press the DIGITAL IN button on the
ADAT to use the DIGITAL INPUT.
23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha 03D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Yamaha 03D

Yamaha 03D Bedienungsanleitung - Deutsch - 307 seiten

Yamaha 03D Bedienungsanleitung - Holländisch - 302 seiten

Yamaha 03D Bedienungsanleitung - Französisch - 300 seiten

Yamaha 03D Bedienungsanleitung - Italienisch - 301 seiten

Yamaha 03D Bedienungsanleitung - Portugiesisch - 141 seiten

Yamaha 03D Bedienungsanleitung - Spanisch - 315 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info