Bedienungsanleitung Yamaha 03D (Seite 35 von 89) (Englisch)

517061

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

30 02R Applications

Yamaha 02R & 03D Applications Guide

02R with Two DA-88s

This application shows how the 02R can be used with two Tascam DA-88s to create a

24-input, 16-track digital recording system. The 16 tape returns and 24 Mic/Line inputs

provide up to 40 inputs at mixdown. In addition, the 02R’s built-in automation and scene

memory systems provide both dynamic and static mix automation referenced to timecode.

Connections

• The Tascam (CD8-TD) cards must be screwed securely in place. Do not leave the screws

out after installation as the cards will not be grounded correctly.

• The Tascam digital audio cables (PW-88DL) carry the eight tape sends and returns.

• DA-88–A is connected to Slot [1] of the 02R. These tape inputs correspond to tracks one

through eight. DA-88–B is connected to Slot [2] of the 02R. These tape inputs

correspond to tracks nine through sixteen.

• The optional SY-88 Sync Board is required for DA-88–A. This enables the dedicated

timecode track, which can be re-striped at anytime, and provides SMPTE timecode and

MTC outputs. A timecode offset can be speciﬁed on DA-88–A, so the 02R automix start

time can be adjusted.

02R Wordclock Setup

On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.

DA-88 Wordclock Setup

DA-88–A works as wordclock master. Wordclock is fed to the 02R using a BNC to BNC

cable, and to the DA-88–B using a PW-88S 15-pin sync cable. The sampling rate is set when

the DA-88 tapes are formatted. This can be either 48 kHz or 44.1 kHz. After formatting, the

sampling rate is determined by the formatted tape.

Notes

• The DA-88s must be powered up even when they are not being used. Failure to do so may

cause an intermittent pumping noise on the 02R.

• DA-88–A is set to MACHINE ID 0. DA-88–B is set to MACHINE ID 1. Since DA-88–A

works as Control Master, it should be used for synchronized transport and locate

operations.

• The optional Tascam SY-88 Sync Board must be installed in DA-88–A to use SMPTE

timecode and MTC. This is available from Tascam. DA-88–B does not require the SY-88

Sync Board nor does its tape have to be striped with timecode. It is synchronized to

DA-88–A via the PW-88S 15-pin sync cable.

• The terminator bundled with the PW-88S sync cable should be connected to the SYNC

OUT on DA-88–B to ensure reliable synchronization.

• The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP

switches 2 and 5 to ON (O). Set internal switch 8 on the SY-88 board marked S2 to ON.

• To use the MTC function, the SY-88 ﬁrmware must be version 3.08 or higher.

• On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is

the initial setting, but you should conﬁrm it. This switch is for use with Tascam High-Bit

recording applications.

• Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m), and the 15-pin

PW-88S sync cable are available from Tascam.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 03D Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 03D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info