Bedienungsanleitung Yamaha 03D (Seite 37 von 89) (Englisch)

517061

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

32 02R Applications

Yamaha 02R & 03D Applications Guide

02R with Four DA-88s

This application shows how the 02R can be used with four Tascam DA-88s to create a

24-input, 32-track digital recording system, providing 32-track digital mixdown. In

addition, the 02R’s built-in automation and scene memory systems provide both dynamic

and static mix automation referenced to timecode.

Connections

• The Tascam (CD8-TD) cards must be screwed securely in place. Do not leave the screws

out after installation as the cards will not be grounded correctly.

• DA-88–A is connected to Slot [1] of the 02R and the tape inputs correspond to tracks

one through eight (Tape In 1–8). DA-88–B is connected to Slot [2] of the 02R and the

tape inputs correspond to tracks nine through sixteen (Tape In 9–16). DA-88–C is

connected to Slot [3] of the 02R and the tape inputs correspond to tracks 17 through 24

(Line In 1–8). DA-88–D is connected to Slot [4] of the 02R and the tape inputs

correspond to tracks 25 through 32 (Line In 9–16).

• The optional SY-88 Sync Board is required for DA-88–A. This enables the dedicated

timecode track, which can be re-striped at anytime, and provides SMPTE timecode and

MTC outputs. A timecode offset can be speciﬁed on DA-88–A.

02R Wordclock Setup

On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.

DA-88 Wordclock Setup

DA-88–A works as wordclock master. Wordclock is fed to the 02R using a BNC to BNC

cable, and to the other DA-88s using PW-88S 15-pin sync cables. The sampling rate is set

when the DA-88 tapes are formatted. This can be either 48 kHz or 44.1 kHz. After

formatting, the sampling rate is determined by the formatted tape.

Notes

• The DA-88s must be powered up even when they are not being used. Failure to do so may

cause an intermittent pumping noise on the 02R.

• DA-88–A is set to MACHINE ID 0, DA-88–B to MACHINE ID 1, DA-88–C to

MACHINE ID 2, and DA-88–D to MACHINE ID 3. Since DA-88–A works as the

Control Master, it should be used for synchronized transport and locate operations.

• The optional Tascam SY-88 Sync Board must be installed in DA-88–A to use SMPTE

timecode and MTC. This is available from Tascam. The other DA-88s do not require

SY-88 Sync Boards and their tapes do not have to be striped with timecode. They are

synchronized to DA-88–A via the PW-88S 15-pin sync cables.

• The terminator bundled with a PW-88S sync cable should be connected to the SYNC

OUT on DA-88–D to ensure reliable synchronization.

• The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP

switches 2 and 5 to ON (O). Set internal switch 8 on the SY-88 board marked S2 to ON.

• To use the MTC function, the SY-88 ﬁrmware must be version 3.08 or higher.

• On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is

the initial setting, but you should conﬁrm it. This switch is for use with Tascam High-Bit

recording applications.

• Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m), and the 15-pin

PW-88S sync cable are available from Tascam.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 03D Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 03D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info