Bedienungsanleitung Yamaha AN1X (Seite 101 von 122) (Englisch)

48724

101

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

101

Voice Creation Examples

Following are examples for creating some of the most common synthesizer sounds, including Synth

Bass, Strings, Electric Piano, Electronic Organ, Synth Brass and Synth Lead. Taking the time to work

through the simple steps to create each will give you a deeper understanding of how the various tone

generator parameters work together, as well as how to practically apply the Control Matrix.

Next let’s tweak a few parameters to add extra

depth and dimension to the sound…

6. Fine-adjust the sensitivity, filter and FEG.

Press KNOB PARAMETER GROUP switch [VCF], then

press CONTROL knob 8 once to display the Vel Sens

(Velocity Sensitivity) parameter in the LCD. Turn the

knob to set a value of about “+30”, to increase the

sensitivity applied to the VCF with playing strength.

Next, use CONTROL knob 5 to further adjust the VCF

Cutoff. Use knob 7 to set the FEG Depth to your liking,

and use knob 8 to further define the Vel Sens

according to your playing style.

The Velocity Sensitivity setting affects the rate of change of the FEG Depth. The

FEG Depth setting determines the range of the change.

7. Set up the synth bass sound for legato play.

Set the [EDIT ROTARY] switch to the VOICE SCENE

SETUP menu and press Poly [UP/DOWN] to set the

Poly mode to “legat” (legato). Playing the keyboard

produces only a monophonic note, and you can slur

the bass notes into each other.

8. Fatten up the sound with Unison play.

Press the [LAYER] switch once to select the Unison

mode. (“UNISON” appears accordingly in the right

area of the LCD.) This produces a much thicker sound

when you play, stacking up five sounds with each note.

9. Boost the filter resonance.

Press KNOB PARAMETER GROUP switch [VCF] and

press CONTROL knob 6 to display the Resonance

parameter in the LCD. Turn the knob to set a value of

about “60”, which will emphasize the harmonics near

the cutoff frequency.

NOTE

Synth Bass

First let’s create the fundamental sound…

1. Select a voice that you don't mind writing

over.

Perform a Type 1 (Normal) Voice Initialize operation.

2. Set the oscillator with a low interval for bass.

Press KNOB PARAMETER GROUP switch [VCO1], then

press CONTROL knob 2 once to display the Pitch

parameter in the LCD. Turn the knob to set a value of “-

12”, which is an octave lower than the basic pitch.

3. Filter out the roughness.

Press KNOB PARAMETER GROUP switch [VCF], then

press CONTROL knob 5 once to display the VCF

Cutoff parameter in the LCD. Turn the knob to set a

value somewhere near “60”, which results in a much

rounder, or smoother sound.

4. Tighten up the sustain.

Press CONTROL knob 3 to display the Sustain

parameter in the LCD. Turn the knob to set a value

near “0”, which will get rid of the flabbiness of the

sound.

5. Beef up the volume.

Press KNOB PARAMETER GROUP switch [VCA], then

press CONTROL knob 6 once to display the Volume

parameter in the LCD. Turn the knob to set a value

near “110” to increase the overall level of the sound.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha AN1X Seite 101

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha AN1X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info