Bedienungsanleitung Yamaha AN1X (Seite 103 von 122) (Englisch)

48724

103

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

103

8. Set the velocity sensitivity of the VCA.

Press KNOB PARAMETER GROUP switch [VCA], then

press CONTROL knob 8 to display the Vel Sens

(Velocity Sensitivity) parameter in the LCD. Turn the

knob to set a value near “+15” to increase the

sensitivity.

9. Adjust the cutoff frequency and set the

velocity sensitivity of the VCF.

Press KNOB PARAMETER GROUP switch [VCF], then

press CONTROL knob 5 once to display the VCF

Cutoff parameter in the LCD. Turn the knob to set a

value near “75” to soften the sound.

Press CONTROL knob 8 once to display the Vel Sens

(Velocity Sensitivity) parameter in the LCD. Turn the

knob to set a value near “+15”, to increase the

sensitivity applied to the VCF with playing strength.

Next, use CONTROL knob 5 to further adjust the VCF

Cutoff. Use knob 7 to set the FEG Depth to your liking,

and use knob 8 to further define the Vel Sens

according to your playing style.

The Velocity Sensitivity setting affects the rate of change of the FEG Depth. The

FEG Depth setting determines the range of the change.

10. Apply vibrato to the voice.

Press KNOB PARAMETER GROUP switch [VCO1] and

press CONTROL knob 8 to display the Pmod Depth

(Pitch Modulation Depth) parameter in the LCD. Turn

the knob to set a value of about “+20”. This applies

the vibrato effect to the voice when you play.

Next, let’s set up the vibrato to be applied by the

[MODULATION] wheel, in order to control the amount

of vibrato as you play. Change the Pmod Depth setting

back to “0”.

We’ll use one of the 16 sets in the Control Matrix to

assign the VCO1 Pitch Modulation Depth parameter to

the [MODULATION] wheel.

Set the [EDIT ROTARY] switch to the VOICE SCENE

SETUP menu.

• Press Set No [UP/DOWN] to display “Set 1” in the

LCD.

• Press Param [UP/DOWN] to display “VCO1

PmodDp” in the LCD.

• Press Source [UP/DOWN] to display “A.MW” in the

LCD.

You can also assign a Control Change number to the Source, by which to control

the Parameter. In this case the Control Change number must match the setting in

the UTILITY SETUP menu’s Control Device and Control Number.

NOTE

You can control the vibrato of the VCO1 by moving the

[MODULATION] wheel. To further define the range of

vibrato control, press Depth [UP/DOWN] to set a

value of “Dp+20”.

We’ll use another Control Matrix set to assign the

VCO2 Pitch Modulation Depth parameter also to the

[MODULATION] wheel.

• Press Set No [UP/DOWN] to display “Set 2” in the

LCD. “Param Off” will also be indicated.

• Press Param [UP/DOWN] to display “VCO2

PmodDp” in the LCD.

• Press Source [UP/DOWN] to display “A.MW” in the

LCD.

You can control the vibrato of the VCO2 by moving the

[MODULATION] wheel. To further define the range of

vibrato control, press Depth [UP/DOWN] to set a

value of “Dp+20”.

Try setting different Control Matrix Depth values to the VCO1 and VCO2 to hear

the effect produced.

There are many other parameters you may

want to adjust to get just the right sound you

want. When you’re finished with the editing

process, perform a Voice Store operation to

store your creation. For information, see page

98.

NOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha AN1X Seite 103

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha AN1X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info