Bedienungsanleitung Yamaha CLP-411 (Seite 27 von 54) (Englisch)

590692

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

The Function Mode

F3.5: 1st Voice Effect Depth............................................................................................................

F3.6: 2nd Voice Effect Depth..........................................................................................................

These functions make it possible to individually set the depth of the chorus effect for the

1st and 2nd dual-mode voices (“1st” and “2nd” refer to the left and right voice selectors,

respectively). Use the [–/NO] and [+/YES] buttons to set the effect depth for the correspond-

ing voice as required. The depth range is from 0 through 20. A setting of “0” produces no

effect, while a setting of “20” produces maximum effect depth. Press the [–/NO] and [+/YES]

buttons simultaneously to recall the default setting (the default effect depth setting is different

for each voice).

NOTE

• The effect depth settings cannot be changed unless the EFFECT is ON. The Function mode must be

exited before EFFECT can be turned ON.

F3.7: (CLP-511) Slow-attack Strings ......................................................................................

In a dual mode voice combination using a strings voice and any other voice, a better

“blend” can sometimes be produced by switching the strings voice to a slow-attack variation.

Use the [–/NO] and [+/YES] buttons to turn the slow-attack variation “On” or “OFF”, as

required. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting:

“OFF”.

F3.7: (CLP-411), F3.8: (CLP-511) Reset ...............................................................................

This function resets all dual-mode functions to their default values. Press the [+/YES]

button to reset the values. “End” will appear on the display when all functions have been

reset.

(CLP-511) Split Mode Functions

After selecting “F4.Y”, press the [+/YES] button to engage the split-mode function sub-

mode, then use the [<] and [>] buttons to select the desired split mode function, as listed

below.

If the Split mode is not engaged “F4.-” will appear instead of “F4.Y” and the Split mode

functions cannot be selected. Also note that you must exit from the Function mode before the

Split mode can be engaged.

■ SHORTCUT: You can jump directly to the split-mode functions (F4) by pressing the

[FUNCTION] button while holding the [SPLIT] button.

F4.1: Split Point ............................................................................................................................................

In addition to the split point setting method described on page 11, the split point can be set

via this function. Use the [–/NO] and [+/YES] buttons to set the split point as required, or

simply press the appropriate key on the keyboard: from “A-1” to “C7”. Press the [–/NO] and

[+/YES] buttons simultaneously to recall the default setting: “F#2”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CLP-411 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CLP-411

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info