Bedienungsanleitung Yamaha CP5 (Seite 47 von 68) (Englisch)

516892

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Using the Stage Piano with a Computer

CP5/CP50 Owner’s Manual 47

Quick Start Guide

2Install the USB MIDI driver on your computer.

For instructions, refer to the Installation Guide included in the downloaded file package. When prompted to connect

the [USB TO HOST] port on your instrument (i.e., the CP5 or CP50) to the computer using a USB cable, do so as

shown below.

3Setup your CP5 or CP50 to allow MIDI data to be exchanged via the [USB TO HOST] port.

Navigate to Page 6 of the Utility screen by pressing the [UTILITY] button, and if necessary, the [6] button. (See the

Reference Manual pdf document for more details.) Turn Knob 2 to set the In/Out parameter (MIDI In/Out) to “USB”.

NOTE If you wish to connect your CP5 or CP50 to a computer via MIDI cables, the In/Out parameter should be set to “MIDI”.

4Press the [STORE] button to store this setting.

Utility settings are stored within User Memory as part of the stage piano’s system settings. For details regarding the

storing procedure, refer to page 50.

Precautions when using the [USB TO HOST] port

When connecting your CP5 or CP50 to a computer via the [USB TO HOST] port, be sure to observe the following precautions.

Failing to do so risks freezing either or both of the devices and corrupting or losing data. If your stage piano or computer should

freeze, restart the application being used, reboot the computer, or turn the stage piano off once and then back on.

• Ensure that an AB-type USB cable is used.

• Before connecting to a computer via the [USB TO HOST] port, restore it from any power-saving mode (such as Suspend, Sleep,

or Standby).

• Connect the computer via the [USB TO HOST] port before turning on your CP5 or CP50.

• Be sure to always perform the following steps before turning the stage piano on or off and either plugging or unplugging a USB

cable.

- Quit all applications.

- Ensure that no data is being sent from the stage piano. (Data is transmitted by playing the keyboard.)

• When connected to a computer, allow at least 6 seconds to pass between turning the stage piano on and off and plugging or

unplugging the USB cable.

HINT

Selecting Performances from a Computer via MIDI

Performances on your CP5 or CP50 can be selected by sending MIDI messages from an application running on a connected

computer. In specific terms, the following three MIDI messages must be sent to the instrument in order to successfully change

Performances.

• Bank select MSB

• Bank select LSB

• Program change

See the MIDI Data Table from the Data List pdf document for details regarding the bank select MSB, bank select LSB, and

program change values assigned to each Performance.

CP5 Computer

USB cable

[USB TO HOST] port USB port

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CP5 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CP5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info