Bedienungsanleitung Yamaha CS6R (Seite 156 von 196) (Englisch)

48734

156

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

156

Phrase Clip Mode

■ Length

Set the Variation length ratio. You can change the

length of all the equal-sized sections by the amount

set here. If you select “toEnd,” the End Point of the

source Phrase Clip will be used as the End Point of

the Variation (after it has been divided).

❏ Settings: toEnd, 10 ~ 800%

If this setting is outside the End Point of the Phrase

Clip, it will be automatically limited to the End Point

setting.

PCLP VarAuto (Variation Auto-set)

The Start Point of the Variation is assigned

automatically. The Loop and End Points are the same

as those set in the original Phrase Clip.

There may be cases that automatic setting is not available

when the Clip has a narrow dynamic range (no big

difference between loudest and smallest volume levels)

because of the entire recorded level is too low, etc.

At this screen, Variation Set 1 to 8 are assigned to each

of the white notes of the keyboard in the range C3 to

C4. Press each note to switch to the respective

Variation Set, then set each Set’s parameters. Finally,

press the [ENTER] key to execute the Job.

If you are not satisfied with the result, try repeating the

process as you may get different results.

■ Threshold

Set the threshold level at which the Auto-set process

is started.

The Start Point is automatically set when the

average level of the Phrase Clip reaches or exceeds

this value.

❏ Settings: 0 ~ 255

■ Adjust

Set the amount by which the automatically-set Start

Point is adjusted (moved forward).

❏ Settings: -255 ~ 0

If the automatic setting is incorrect, Variation Set 1 will

be set such that the entire length of the Phrase Clip will

be played back. In this case the Start, Loop and End

Points for Variation Sets 2 to 8 will be set to zero.

PCLP VarRealTime (Variation Real-time)

You can set the Start Point of the Variation in real-time

while listening to the Loop. The Loop and End Points

remain in the same positions as set for the Phrase Clip.

The procedure is as follows.

PCLP VarRealTime) Hit[C3-C4] [EXIT]

Job C 2:001[SmplName] toVar1-8 toStop

PCLP VarAuto) Threshold Adjust

Job C 2:001[SmplName] 255 -255

1At this screen, you can play back the currently

selected Phrase Clip as a loop.

2Set the Start Points for Variations 1 to 8 by pressing

notes C3 to C4 on the keyboard.

By pressing the white notes (C3 to C4) on the

keyboard corresponding to Variation Sets 1 to 8, you

can set the Start Point while listening to the sound.

3In the same way, press the notes when setting the

Start Points for the other Variation Sets.

4When you press the [EXIT] key, you will see the

confirmation message. At this screen, you can verify

by playing Variation Sets 1 to 8 by pressing the white

notes on the keyboard between C3 and C4.

5Press the [INC/YES] key to set each Variation, or

press the [DEC/NO] key to cancel the operation and

return the Variation to its original state.

PCLP Var (Variation Manual)

You can change the settings for the Variation of the

currently selected Phrase Clip. Use Knob [A] to select

from Variation Sets 1 to 8 and use Knobs [B], [C], [1]

and [2] to set its parameters. Then press the [ENTER]

key to execute the Job.

At this screen, the white notes on the keyboard

between C3 and C4 can be used to select and play

Variation Sets 1 to 8.

■ Var (Variation Number)

Select the Variation you wish to set. The settings for

the selected Variation will be reflected in all

parameters.

❏ Settings: 1 ~ 8

■ Play (Play Mode)

Select the Phrase Clip playback mode. There are

three modes.

❏ Settings:

loop:

When you press a note on the keyboard, the Phrase Clip is

played completely from its Start Point. Then its looped

section is played back repetitively until you release the note.

oneshot:

When you press a note on the keyboard, the Phrase Clip is

played just once from its Start Point to its End Point (not

looped).

reverse:

When you press a note on the keyboard, the Phrase Clip is

played in reverse, just once, from its End Point to its Start

Point (not looped).

Basic details about each mode are given on Page 54.

PCLP Var) Play Start Loop End

Var=1: oneshot 2097150 2097150 2097150

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CS6R Seite 156

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CS6R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info