Bedienungsanleitung Yamaha CS6R (Seite 157 von 196) (Englisch)

48734

157

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

157

Phrase Clip Mode

■ Start (Start Point)

Set the Start Point from which the Phrase Clip will

be played back. By finely adjusting the Start Point,

you can avoid playback of the noise before the Start

Point. This setting, however, does not eliminate the

noise in the original Clip.

❏ Settings: Depends on the length of the Phrase Clip.

■ Loop (Loop Point)

Set the starting point of the looped section. With a

violin sound, for example, the Loop Point should be

set after the distinctive attack portion and at the

start of the sustained section of the sound. When

playing back this loop, the attack portion of the

violin sound is played back, followed by the looped

section corresponding with the sustained section of

the violin sound (between the Loop Point and the

End Point). On the other hand, if the sound does

not have a distinctive attack portion, the Loop Point

can be set to the same position as the Start Point.

❏ Settings: Depends on the length of the Phrase Clip.

■ End (End Point)

Set the End Point of the Phrase Clip’s looped section.

This can also be useful for removing unwanted noise

at the end of the Phrase Clip.

❏ Settings: Depends on the length of the Phrase Clip.

Details about the Start, Loop and End Points are given

on Page 150.

PCLP LoopRemix

The Phrase Clip data can be edited and a new Phrase

Clip can be automatically created with a new Loop.

The procedure is as follows.

The following Jobs are available only when the Phrase

Clip has been recorded in 16-bit format.

1Select the Phrase Clip by using Knob [A] to select

the target Clip Key or Knob [B] to set the Phrase Clip

Number.

You can also select the target Clip Key directly by

pressing its note on the keyboard.

2Select the Type parameter which specifies the

section of the Loop to be changed. Five Types are

available.

3Select the Vari (Variation) parameter, which is the

degree of change to be applied to the Loop. Four

Variations (A to D) are available, each offering

increasing degrees of change.

PCLP LoopRemix) Type Vari

JOB C 2:001[SmplName] 1 A

4When you press the [ENTER] key, you will see a

confirmation message. Press the [INC/YES] key to

execute the Loop Remix Job. The Job will be

canceled if you press the [DEC/NO] key.

5After executing the Loop Remix Job, you will see the

following Retry message.

At this screen, you can use the keyboard to audition

the Loop Remix. If you are not satisfied with the

result, try creating another Loop Remix by repeating

steps 2 to 4 but using different Variation settings.

6When you are satisfied with the result, press the

[DEC/NO] key. A new Phrase Clip will be created

and you will be returned to the first screen.

PCLP Normalize

You can normalize each Phrase Clip. This maximizes

the output level of the recorded Phrase Clip without

causing distortion.

To select each Phrase Clip, use Knob [A] to select the

Clip Key or Knob [B] to select the Phrase Clip Number.

After selecting the Phrase Clip, set the Ratio parameter

and press the [ENTER] key to normalize.

You can also select the Clip Key directly by pressing a note

on the keyboard.

■ Clip Key

Select the Clip Key of the target Phrase Clip.

❏ Settings: C0 ~ C6

■ Clip Number

Select the target Phrase Clip.

❏ Settings: 1 ~ 256

■ Ratio

Set an amplitude ratio in normalization of a volume

level. With a value of “100” (%), a peak level will

be normalized into full 16 bits, which means there is

virtually no distortion in resulting levels. If the

volume level in an original Clip is extremely low, set

a value less than “100” (%) for a waveform

smoother in level changes. You can set a value more

than “100” (%) for an intentionally distorted sound.

❏ Settings: 0 ~ 200%

Once you perform this operation on a Phrase Clip, its

original data will be overwritten and you will not be

able to undo the changes. Important data should always

be backed up or copied to a separate Phrase Clip

Number before performing this operation.

PCLP Normalize) Ratio

Job C 2:001[SmplName] 100%

PCLP LoopRemix) Type Vari

<< Retry? [YES]/[NO] >> 1 A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CS6R Seite 157

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CS6R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info