Bedienungsanleitung Yamaha DSP-Z11 (Seite 117 von 150) (Englisch)

464180

117

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Using multi-zone configuration

117 En

Advanced

Operation

3 Perform the operations in the selected zone.

For further operations, refer to the following pages:

To turn off the desired zone, press KZONE 2, KZONE 3, or KZONE 4 again.

Remote control operations

1 Press

ZONE repeatedly to select the zone you

want to control.

“MAIN”, “ZONE 2”, “ZONE 3”, or “ZONE 4” indicator

appears in the display window (4) on the remote control.

2 Press EPOWER to turn on the selected zone.

3 Perform the operations in the selected zone.

For further operations, refer to the following pages:

To turn off the desired zone, press DSTANDBY.

■ Selecting the input source Zone 2, Zone 3, or

Zone 4

Rotate the

INPUT selector on the front panel (or set

the operation mode selector to

AMP and then press

one of the input selector buttons (

)) to select the input

source of the selected zone.

• Select “DOCK” as the input source to use the iPod features in

the selected zone. For details about the iPod operations, see

“Using iPod™” on page 64.

• Select “NET/USB” as the input source to use the network/USB

operations features in the selected zone. For details about the

iPod operations, see “Using Network/USB features” on page 66.

• The selected input sources are shared across all zones.

• If you set the recording source other than “SOURCE” (see page 62), the input source

of Zone 2 is fixed to the source you set as the recording source.

■ Adjusting the volume level of Zone 2, Zone 3, or

Zone 4

Rotate EVOLUME on the front panel (or press

JVOLUME +/–) to adjust the volume level of the

selected zone.

Press

MUTE on the remote control to mute the sound output to the selected zone.

When you use the external amplifiers in Zone 2 or Zone 3,

VOLUME +/– can be

used only when “Zone2 Volume”, “Zone3 Volume”, or “Zone4 Volume” is set to

“Variable” in “Zone2 Set”, “Zone3 Set”, or “Zone4 Set” (see page 91).

■ Setting the sleep timer for Zone 2, Zone 3, or

Zone 4

Use this feature to turn off the desired zone to the standby mode

after a contain amount of time.

Set the operation mode selector to FAMP on the remote

control and then press CSLEEP repeatedly to set the

amount of time.

Each time you press CSLEEP, the sleep timer setting changes as

shown below.

Descriptions

Page

“Selecting the input source Zone 2, Zone 3, or Zone 4” 117

“Adjusting the volume level of Zone 2, Zone 3, or Zone 4” 117

“Adjusting the tonal quality of Zone 2, Zone 3, or Zone 4” 118

Descriptions

Page

“Selecting the input source Zone 2, Zone 3, or Zone 4” 117

“Adjusting the volume level of Zone 2, Zone 3, or Zone 4” 117

“Adjusting the tonal quality of Zone 2, Zone 3, or Zone 4” 118

MAIN

ZONE 2 ZONE 3

ZONE 4

(Zone 2) (Zone 3) (Zone 4)

(Main zone)

Operate the following operations after activating the Zone 2, Zone 3, or Zone 4

operation mode.

Notes

Note

120min. 90min.

60min.30min.OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha DSP-Z11 Seite 117

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha DSP-Z11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info