Bedienungsanleitung Yamaha DSP-Z11 (Seite 122 von 150) (Englisch)

464180

122

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Troubleshooting

122 En

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction

below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.

■ General

Troubleshooting

Problem Cause Remedy See page

This unit fails to turn on or

enters the standby mode

soon after the power is

turned on.

The power cable is not connected or the plug is not

completely inserted.

Connect the power cable firmly.

—

The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers.

The protection circuitry has been activated. Make sure that all speaker wire connections on this unit and on

all speakers are secure and that the wire for each connection

does not touch anything other than its respective connection.

This unit has been exposed to a strong external

electric shock (such as lightning or strong static

electricity).

Set this unit to the standby mode, disconnect the power cable,

plug it back in after 30 seconds and then use it normally.

—

No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables

may be defective.

30-38

Audio input jack select is set to “HDMI”, “Coax/

Opt” or “Analog”.

Set the audio input jack select to “Auto”.

Audio input jack select is set to “Analog” while

the input source component outputs digital audio

signals.

Set the audio input jack select to “Auto” or

“Coax/Opt”.

No appropriate input source has been selected.

Select an appropriate input source with the

INPUT selector

on the front panel (or the input selector buttons (3) on the

remote control).

Speaker connections are not secure. Secure the connections.

The volume is turned down. Turn up the volume.

—

The front speakers to be used have not been

selected properly.

Select the front speakers by pressing GSPEAKER A or

GSPEAKER B on the front panel.

The sound is muted.

Press

MUTE or

VOLUME +/– on the remote control to

resume audio output and then adjust the volume.

Signals this unit cannot reproduce are being input

from a source component, such as a CD-ROM.

Play a source whose signals can be reproduced by this unit.

—

The HDMI components connected to this unit do

not support the HDCP copy protection standards.

Connect HDMI components that support the HDCP copy

protection standards.

“Support Audio” is set to “Other” and HDMI

audio signals are not being played back on this

unit.

Set “Support Audio” in “Option” to “DSP-Z11”.

No picture. The output and input for the picture are connected

to different types of video jacks.

Set “Conversion” to “On” or connect your source components

in the same way as you connect your video monitor to this unit.

This unit outputs the video signals are not

supported in the video monitor connected to the

HDMI OUT jack.

Set the “INITIALIZE” to “VIDEO” to reset the video

parameters.

120

Set “MONITOR CHECK” to “YES”.

120

Input selector setting of the video monitor is

incorrect.

Set the input source selector setting of the video monitor

appropriately.

—

Pure Direct mode is active. Turn off the Pure Direct mode.

—

Set “Pure Direct” in “Sound” to “Video On”.

Non-standard video signals are input.

The HDMI OUT jack that the video monitor is

connected is not selected.

Press CHDMI OUT on the remote control repeatedly.

Short message displays in

the main zone do not

appear in the video

monitor.

“Short Message” is set to “Off”. Set “Short Message” to “On”.

“Conversion” is set to “Off”. Set “Conversion” to “On”.

The signals input at the HDMI input jacks are

being output at the HDMI OUT jack.

The sound suddenly goes

off.

The protection circuitry has been activated because

of a short circuit, etc.

Check that the speaker impedance setting is correct.

39, 119

Check that the speaker wires are not touching each other and

then turn this unit back on.

—

The sleep timer has turned off this unit. Turn on this unit, and play the source again.

—

The sound is muted.

Press

MUTE or

VOLUME +/– on the remote control to

resume audio output.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha DSP-Z11 Seite 122

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha DSP-Z11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info