Bedienungsanleitung Yamaha DSP-Z11 (Seite 123 von 150) (Englisch)

464180

123

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Troubleshooting

123 En

Additional

Information

Sound is heard from the

speaker on one side only.

Incorrect cable connections. Connect the cables properly. If the problem persists, the cables

may be defective.

Incorrect settings in “Speaker Level”. Adjust the “Speaker Level” settings.

Only the center speaker

outputs substantial sound.

When playing a monaural source with a CINEMA

DSP program, the source signal is directed to the

center channel, and the front and surround

speakers output effect sounds.

No sound is heard from the

center speaker.

“

Center

” in “

Speaker Set

” is set to “

None

”.

Set “Center” to “Small” or “Large”.

One of the HiFi DSP programs (except for “11ch

Stereo”) has been selected and analog 2-channel

source is being input.

Try another sound field program if you want to output sound

from the center speaker.

No sound is heard from the

presence speakers.

The sound field programs are turned off.

Press

STRAIGHT to turn them on.

You are using a source or program combination

that does not output sound from all channels.

Try another sound field program.

No sound is heard from the

surround speakers.

“

Surround

” in “

Speaker Set

” is set to “

None

”.

Set “Surround” to “Small” or “Large”.

This unit is in the “STRAIGHT” mode and a

source which does not contain the surround

channel signals is being played back.

Press

STRAIGHT on the front panel so that “STRAIGHT”

disappears from the front panel display.

No sound is heard from the

subwoofer.

“Bass Out” in “Speaker Set” is set to “Front” when

a Dolby Digital or DTS signal is being played.

Set “Bass Out” to “SWFR” or “Front & SWFR”.

“Bass Out” in “Speaker Set” is set to “SWFR” or

“Front” when a 2-channel source is being played.

Set “Bass Out” to “Front & SWFR”.

The source does not contain low-frequency

signals.

No sound is heard from the

surround back speakers.

“Surround” in “Speaker Set” is set to “None” and

“Surround Back” is automatically set to “None”.

Set “Surround” and “Surround Back” to a setting other than

“None”.

“Surround Back” in “Speaker Set” is set to

“None”.

Set “Surround Back” to a setting other than “None”.

The audio input sources

cannot be played in the

desired digital audio signal

format. (Desired input

source indicator or

decoder indicator in the

front panel display does

not light up.)

The connected component is not set to output

Dolby Digital or DTS digital signals.

Make an appropriate setting following the operating instructions

for your component.

—

Audio input jack select is set to “Analog”. Set the audio input jack select to “Auto”.

A humming sound is

heard.

Incorrect cable connections. Connect the audio cables firmly. If the problem persists, the

cables may be defective.

—

No connection from the turntable to the GND

terminal.

Connect the grounding cable of the turntable to the GND

terminal on this unit.

The volume level is low

while a record is being

played.

The record is being played on a turntable with an

MC cartridge.

Connect the turntable to this unit through an MC-head amplifier.

The volume level cannot

be increased, or the sound

is distorted.

The component connected to the AUDIO OUT

jacks of this unit is turned off.

Turn on the power of the component.

—

The sound effect cannot

be recorded.

It is not possible to record the sound effect with a

recording component.

A source cannot be

recorded by a digital

recording component

connected to the DIGITAL

OUTPUT jack.

The source component is not connected to the

DIGITAL INPUT jacks on this unit.

Connect the source component to the DIGITAL INPUT jacks.

31, 34

Some components cannot record Dolby Digital or

DTS sources.

A source cannot be

recorded by an analog

component connected to

the AUDIO OUT jacks.

The source component is not connected to the

analog AUDIO IN jacks on this unit.

Connect the source component to the analog AUDIO IN jacks.

The sound field

parameters and some

other settings of this unit

cannot be changed.

“Memory Guard” in “Option” is set to “On”. Set “Memory Guard” to “Off”.

This unit does not operate

properly.

The internal microcomputer has been frozen by an

external electric shock (such as lightning or

excessive static electricity) or by a power supply

with low voltage.

Disconnect the power cable from the AC wall outlet and then

plug it in again after about 30 seconds.

—

Problem Cause Remedy See page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha DSP-Z11 Seite 123

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha DSP-Z11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info