Bedienungsanleitung Yamaha DSP-Z11 (Seite 127 von 150) (Englisch)

464180

127

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Troubleshooting

127 En

Additional

Information

During Auto Setup

After Auto Setup

• If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “Auto Setup” again.

• If warning “W2” or “W3” appears, the adjustment are made, however the adjustments may not be optimal.

• Depending on the speakers, warning “W1” may appears even if the speakers connections are correct.

• If error “E10” occurs repeatedly, please contact a qualified Yamaha service center.

■ Resetting the system

Use this feature to reset all the parameters of this unit to the initial

factory settings.

• This procedure completely resets all the parameters of this unit including

the GUI menu parameters.

• The initial factory settings are activated next time you turn on this unit.

To cancel the initialization procedure at any time without making any

changes, press

MASTER ON/OFF on the front panel to release it

outward to the OFF position.

1 Press

MASTER ON/OFF on the front panel to

release it outward to the OFF position to turn off this

unit.

2 Press and hold

PROGRAM and then press

MASTER ON/OFF inward to the ON position to

turn on this unit.

Press and hold IPROGRAM until “ADVANCED SETUP”

appears in the front panel display (see page 119).

3 Rotate

PROGRAM to select “INITIALIZE”.

4 Press

PROGRAM repeatedly to select “ALL”.

• Select “CANCEL” to cancel the initialization procedure without

making any changes.

• You can initialize the video parameters or sound field program

parameters separately. See page 120 for details.

5 Press

MASTER ON/OFF to release it outward to

the OFF position to confirm your selection and turn

off this unit.

Error message Cause Remedy See page

E01:No Front SP Front L/R channel signals are not detected. Check the front L/R speaker connections. 23

E02:No Sur. SP A surround channel signal is not detected. Check the surround speaker connections. 23

E03:No F. PRNS SP A front presence channel signal is not detected. Check the front presence speaker connections. 23

E04:SBR → SBL Only right surround back channel signal is detected. Connect the surround back speaker to the

SUR.BACK/BI-AMP (SINGLE) terminal if you

only have one surround back speaker.

E05:Noisy Background noise is too loud. Try running “Auto Setup” in a quiet environment.

—

Turn off noisy electric equipment like air

conditioners or move them away from the optimizer

microphone.

—

E06:Check Sur. Surround back speakers are connected, though

surround L/R speakers are not.

Connect surround speakers when you use surround

back speakers.

E07:No MIC The optimizer microphone was unplugged during

the “Auto Setup” procedure.

Connect the supplied optimizer microphone to the

OPTIMIZER MIC jack on the front panel.

E08:No R.PRNS SP A rear presence channel signal is not detected. Check the rear presence speaker connections. 23

E09:User Cancel The “Auto Setup” procedure was cancelled due to

user activity.

Run “Auto Setup” again. 42

E10:Internal Err. An internal error occurred. Run “Auto Setup” again. 42

Warning message Cause Remedy See page

W1:Out of Phase Speaker polarity is not correct. This message may

appear depending on the speakers even when the

speakers are connected correctly.

Check the speaker connections for proper polarity

(+ or –).

W2:Over Distance The distance between the speaker and the listening

position is over 24 m (80 ft).

Bring the speaker closer to the listening position.

—

W3:Level Error The difference of volume level among speakers is

excessive.

Readjust the speaker installation so that all speakers

are set in locations with similar conditions.

—

Check the speaker connections. 23

Use speakers of similar quality.

—

Adjust the output volume of the subwoofer. 42

W4:SP Mismatch The result of the wiring check of “Auto Setup” is

different from “Speaker Set” in “Manual Setup”.

Use “Speaker Set” in “Manual Setup” to adjust the

speaker settings manually.

“Wiring” check procedure is skipped. Select “Wiring” in “Setup Menu”. 44

Notes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha DSP-Z11 Seite 127

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha DSP-Z11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info