Bedienungsanleitung Yamaha ES7 (Seite 71 von 300) (Englisch)

48742

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Playing the Keyboard (in the Performance Play mode)

Owner’s Manual

Quick Guide — Playing the MOTIF ES

This calls up a list indicating which Voice is assigned to each

Part of the current Performance.

Move the cursor to the desired Part. When a Voice has

already been assigned to the selected Part, change the Voice

Bank or Number by using the data dial, the [INC/YES] and the

[DEC/NO] button. When no Voice is assigned to the selected

Part, press the [SF1] ADD INT button or [SF2] ADD PLG

button to execute the assignment, then change the Voice

Bank or Number.

You can also select a Voice Bank/Number by using the BANK,

GROUP, and NUMBER buttons (page 60).

nVoices of the Multi part Plug-in Board PLG100-XG cannot be assigned

to Performance parts.

When an internal Voice is assigned to a Part, the following

Voice Banks are available.

When a Plug-in Board Voice is assigned to a Part, the

available Voice Banks differ depending on the installed Plug-

in Board. For details, refer to the Owner’s Manual that came

with the Plug-in Board.

You can set the lowest note of the range over which the Voice

of the selected Part sounds by simultaneously holding the

[SF4] button and pressing the desired key. To set the highest

note of the range, simultaneously hold the [SF5] button and

press the desired key.

Press the [STORE] button to enter the Performance Store

mode, select the destination Performance number, then press

the [ENTER] button to execute the store operation. For details

about Performance Store, see page 91.

1Press the [F2] VOICE button in the Performance

Play mode.

2Assign the desired Voice to each Part.

SCENE SF1 SF2SF3SF4SF5

F1F2F3F4F5F6

INFORMATION

SCENE SF1 SF2SF3SF4SF5

F1F2F3F4F5F6

INFORMATION

DEC/NO INC/YES

Select a Voice

Bank/Number at

the cursor location.

Voice Bank Voice Number

Assign an internal Voice

to the selected Part.

Delete the Voice assignment of the

selected Part.

Assign a Plug-in Voice to the selected Part.

(Available when the Plug-in Board has been installed.)

PRE1 (Preset1) ~

PRE6 (Preset 6) Preset Banks 1 - 6 of the Normal Voice. These

correspond to the [PRE1] - [PRE6] buttons in the Voice

mode.

USER1 ~ USER2 User Banks 1 - 2 of the Normal Voice. These correspond

to the [USER1] - [USER2] buttons in the Voice mode.

GM GM Normal Voice Bank. This corresponds to the [GM]

button in the Voice mode.

PDR (Preset Drum) Preset Bank of the Drum Voice. This corresponds to

pressing the [DRUM KITS] button and the [PRE5] button

simultaneously.

GMDR (GM Drum) GM Drum Voice Bank. This corresponds to pressing the

[DRUM KITS] button and the [GM] button simultaneously.

UDR (User Drum) User Bank of the Drum Voice. This corresponds to

pressing the [DRUM KITS] button and the [USER1]

button simultaneously.

3Specify the note range of each part, as required.

4Change the volume of each Part and adjust the

relative balance among the four Parts by using

the Control sliders.

5Store the settings as a User Performance in the

Performance Store mode.

SF 4 SF 5

Note Limit Low Note Limit High

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha ES7 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info