Bedienungsanleitung Yamaha F02 (Seite 38 von 52) (Englisch)

599464

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Appendix

F02 Owner’s Manual

To turn off the message, press [-/NO].

Uoc

Communication with the USB flash memory has been shut down because of overcurrent to the USB flash

memory. Disconnect the USB flash memory from the [USB TO DEVICE] terminal, then turn on the power of

the instrument again.

UU1

Communication with the USB flash memory has failed. Remove the USB flash memory and make the

connection again. If the message appears even when the USB flash memory is connected properly, the USB flash

memory may be damaged.

UU2

This USB flash memory is not supported on this instrument, or too many USB flash memories may have been

connected. Refer to “Handling a USB Flash Memory” (page 28) for information on the USB flash memory

connection.

Troubleshooting

Problem Possible Cause and Solution

The instrument does not turn on. The instrument has not been plugged in properly. Securely insert the female

plug into the socket on the instrument, and the male plug into a proper AC

outlet (page 13).

A click or pop is heard when the power is turned on

or off.

This is normal when electrical current is being applied to the instrument.

Noise is heard from the speakers or headphones. The noise may be due to interference caused by the use of a mobile phone in

close proximity to this instrument. Turn off the mobile phone, or move it

further away from this instrument

Noise is heard from the instrument’s speakers or

headphones when using the instrument with the

application on iPhone/iPad.

When you use the instrument along with the application on your iPhone/

iPad, we recommend that you set “Airplane Mode” to “ON” on your iPhone/

iPad in order to avoid noise caused by communication.

The overall volume is low, or no sound is heard. The volume is set too low. Set it to an appropriate level using the [VOLUME]

slider (page 14).

Make sure a pair of headphones is not connected to the headphones jack

(page 13).

Make sure that Local Control is On (page 34).

The damper pedal does not function as expected. The damper pedal was pressed when the power was turned on. This is not a

malfunction; release the pedal and press it again to reset the function.

Sound input to the AUX IN jacks is interrupted. The output volume of the external device connected to this instrument is too

low, resulting in the sound being cut off via the Noise Gate after it is input to

this instrument.

• Increase the output volume of the external device. The volume level

reproduced via this instrument’s speakers can be adjusted by using the

[VOLUME] slider.

• Set the Noise Gate to off (page 33).

The USB flash memory has hung up (stopped). Refer to the Message List (page 37) in case a message is displayed. If this

happens without any messages, the USB flash memory may be damaged.

Message Meaning

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha F02 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha F02

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info