Bedienungsanleitung Yamaha HTR-5140RDS (Seite 56 von 68) (Englisch)

549947

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

SETUP CODES

To control your components

(MD recorder, DVD player,

TV, etc.)

1. Turn on the component to be used.

2. Press the component selector which

matches the component to be

controlled (TAPE/MD, DVD/LD, TV

etc.).

3. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

4. Use the numeric buttons to enter the

four-digit manufacturer’s code for

the component to be used. Make

sure that the indicator flashes twice.

If the indicator does not flash, repeat

step 3 and re-enter the code.

5. Press POWER (or any other button)

on the remote control transmitter to

check if you have preset the code

correctly. If the component cannot

be controlled by the remote control

transmitter, try entering another

code for the same manufacturer.

Returning to the factory-set

codes

To return all components to the factory-

set codes, follow these steps.

1. Press a button on the component

selector other than AMP<TUNER>.

2. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

3. Enter the code number “9990”.

4. Make sure that the indicator flashes

twice.

To return each component to the factory-

set codes, follow these steps.

1. Press the component selector which

matches the component to be

returned to the factory-set codes.

2. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

3. Enter the code number “0000”.

4. Make sure that the indicator flashes

twice.

The following codes are preset by the

factory.

Factory-set codes

Component

Component Code

selector

TV TV 0101

CBL/DBS DBS tuner 0006

VCR VCR 0002

DVD/LD DVD player

0008 YAMAHA

CD CD player

0005 YAMAHA

TAPE/MD Tape deck

0004 YAMAHA

We recommend that you write all code

numbers you have preset on the “Quick

Reference Card”.

Presetting the remote control transmitter

Perform the presetting procedure for each component you want to control with the remote control transmitter.

Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control

transmitter that was supplied with the component.

To use a second (and third) VCR

You can control a second (and/or third)

VCR in the CBL/DBS and DVD MENU

modes if a CBL (or DBS) or DVD player

is not being used.

If you want to control a second (and/or

third) VCR in the DVD MENU mode, you

must preset the code for an LD player in

that mode.

1. Turn on the VCR to be used.

2. Press CBL/DBS or DVD MENU on

the component selector.

3. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

4. Use the numeric buttons to enter the

four-digit code for the second (or

third) VCR. Make sure that the

indicator flashes twice. If the

indicator does not flash, repeat step

3 and re-enter the code.

5. Press POWER (or any other button)

on the remote control transmitter to

check if you have preset the code

correctly. If the VCR cannot be

controlled by the remote control

transmitter, try entering another

code for the same manufacturer.

01RX-V495RDS-6 6/22/99, 12:29 PM56

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-5140RDS Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info