Bedienungsanleitung Yamaha HTR-5140RDS (Seite 58 von 68) (Englisch)

549947

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

SYMPTOM

No sound from the center speaker.

The sound field cannot be recorded.

The DVD/LD, TV or DBS source

cannot be recorded on a tape deck,

MD recorder or VCR connected to

this unit.

FM stereo reception is noisy.

There is distortion and clear

reception cannot be obtained even

with a good FM antenna.

The desired station cannot be tuned

in with the automatic tuning method.

Previously preset stations can no

longer be tuned in.

The desired station cannot be tuned

in with the automatic tuning method.

There are continuous crackling and

hissing noises.

There are buzzing and whining

noises (especially in the evening).

The remote control transmitter does

not work.

CAUSE

The input signals of the source encoded

with Dolby Digital do not have center

channel signals.

The sound output level of the center

speaker is set to minimum.

The function “CNTR” in the SET MENU

is set to the NONE position.

Incorrect sound field program selection.

It is not possible to record the sound

field on a tape deck or MD recorder

connected to the unit’s REC OUT

terminals.

The DVD/LD player, TV or DBS tuner is

connected to the unit by only the digital

terminals.

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

There is multipath interference.

The station is too weak.

This unit has been unplugged for a long

period.

The signal is weak or antenna

connections are loose.

Noise will result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

A television set is being used nearby.

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of the

this unit.

The manufacturer’s code has not been

set properly.

The proper manufacturer’s code for the

component to be controlled has not

been set.

The component to be controlled has not

been selected.

REMEDY

Refer to the instruction for the source

being currently played.

Raise the sound output level of the

center speaker.

Select the LARGE or SMALL position.

Select the appropriate program.

Make additional connections between

the analog terminals.

Check the antenna connections.

Try using a high-quality directional FM

antenna.

Set TUNING MODE to the manual

tuning mode.

Adjust antenna position to eliminate

multipath interference.

Use the manual tuning method.

Use a high-quality directional FM

antenna.

Repeat the presetting procedure.

Tighten the AM loop antenna

connections and rotate it for best

reception.

Use the manual tuning method.

Use an outdoor antenna and a ground

wire. This will help somewhat, but it is

difficult to eliminate all noise.

Relocate this unit away from the TV.

Change the position of the unit.

Set the code again.

Try entering another code for the same

manufacturer.

Press the component selector which

matches the component to be

controlled.

Remote control transmitter

AM FM

Amplifier

01RX-V495RDS-7 6/22/99, 12:29 PM58

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-5140RDS Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info