Bedienungsanleitung Yamaha Montage 8 (Seite 69 von 86) (Englisch)

652605

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

MONTAGE Owner’s Manual

Troubleshooting



Are the volume or expression settings too low?

• In case of Normal Part (AWM2) and Drum Part

• In case of Normal Part (FM-X)

 Are the parameter settings such as Element Switch, Note Limit, Velocity Limit, and Velocity Offset appropriate?

• In case of Normal Part (AWM2) and Drum Part

• In case of Normal Part (FM-X)

 Is the Mute switch for each Element/Operator of Part turned on?

 In case of Normal Part (FM-X), is the Carrier Level is set to “0”?

 Is the output parameter of each Part turned off?

No sound from the A/D INPUT jack.

 Is the switch of the microphone turned on?

 Check the microphone type. Make sure to use a dynamic microphone.

 Is the cable between the microphone or audio equipment and this instrument properly connected?

 Is the A/D INPUT [GAIN] knob turned to the minimum?

 Is the A/D INPUT [ON/OFF] button turned on?

 Check whether or not the connection status of the A/D INPUT [L/MONO]/[R] matches the “Mono/Stereo” parameter.

 Check whether or not the “Mic/Line” parameter is set to the appropriate value.

When the output level of the connected equipment (such as a microphone) is low, set this parameter to “Mic.” When the

output level of the connected equipment (such as a synthesizer keyboard, CD player) is high, set this parameter to “Line.”

 Are the volume settings of the A/D Input Part too low?

 Are the effect settings appropriate?

 Is the output setting of the A/D Input Part set appropriately?

 Check whether or not the Vocoder Effect is selected.

When Vocoder is selected as the Insertion Effect for the current Part, the audio signal input from the A/D INPUT [L/MONO]/[R]

jacks may not produce any sound depending on the parameter settings.

[UTILITY]  [Settings]  [Sound]  Tone Generator “Volume”

[EDIT]  PART [COMMON]  [General]  “Volume”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]  “Volume”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]  “Dry Level”

[EDIT]  Part selection  Element/Key selection  [Amplitude]  [Level/Pan]  “Level”

[EDIT]  Part selection  Operator selection  [Level]  “Level”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]

[EDIT]  Part selection  Element/Key selection  [Osc/Tune]

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]

[EDIT]  Part selection  Mute Switch of each Element/Operator

[EDIT]  Part selection  Operator selection  [Level]  “Level”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]  “Part Output”

[EDIT]  PART [COMMON]  [Audio In]  [Mixing]  A/D In “Input Mode”

[UTILITY]  [Settings]  [Audio I/O]  “A/D Input”

[EDIT]  PART [COMMON]  [Audio In]  [Mixing]  A/D In “Volume”

[EDIT]  PART [COMMON]  [Audio In]  [Routing]

[UTILITY]  [Settings]  [Audio I/O]  Output

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Effect]  [Routing]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha Montage 8 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info