Bedienungsanleitung Yamaha MOTIF ES7 (Seite 183 von 300) (Englisch)

571272

183

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

About MIDI

183

Owner’s Manual

Basic Structure

Release Time (Control #072)

Messages which adjust the AEG release time set for each

Part.

The value set here is an offset value which will be added to or

subtracted from the voice data.

Attack Time (Control #073)

Messages which adjust the AEG attack time set for each Part.

The value set here is an offset value which will be added to or

subtracted from the voice data.

Brightness (Control #074)

Messages which adjust the ﬁlter cutoff frequency set for each

Part.

The value set here is an offset value which will be added to or

subtracted from the voice data. Lower values result in a softer

sound.

Depending on the voice, the effective range may be narrower

than the range available for adjustment.

Decay Time (Control #075)

Messages which adjust the AEG decay time set for each Part.

The value set here is an offset value which will be added to or

subtracted from the voice data.

Effect1 Depth (Reverb Send Level) (Control #091)

Messages which adjust the send level for the Reverb effect.

Effect3 Depth (Chorus Send Level) (Control #093)

Messages which adjust the send level for the Chorus effect.

Data Increment (Control #096)

Decrement (Control #097) for RPN

Messages which increase or decrease the MSB value of pitch

bend sensitivity, ﬁne tune, or coarse tune in steps of 1. You will

need to assign one of those parameters using the RPN in the

external device in advance. The data byte is ignored. When

the maximum value or minimum value is reached, the value

will not be incremented or decremented further. (Incrementing

the ﬁne tune will not cause the coarse tune to be

incremented.)

NRPN (Non-Registered Parameter Number)

LSB (Control #098) (Plug-in Board only)

NRPN (Non-Registered Parameter Number)

MSB (Control #099) (Plug-in Board only)

Messages which adjust a voice’s vibrato, ﬁlter, EG, drum

setup or other parameter settings.

First send the NRPN MSB and NRPN LSB to specify the

parameter which is to be controlled. Then use Data Entry

(page 182) to set the value of the speciﬁed parameter.

Note that once the NRPN has been set for a channel,

subsequent data entry will be recognized as the same

NRPN’s value change. Therefore, after you use the NRPN, you

should set a Null (7FH, 7FH) value to avoid unexpected

results.

For details, refer to the owner’s manual of the relevant Plug-in

Board.

RPN (Registered Parameter Number) LSB (Control #100)

RPN (Registered Parameter Number) MSB (Control #101)

Messages which offset, or add or subtract values from a

Part’s pitch bend sensitivity, tuning, or other parameter

settings. First send the RPN MSB and RPN LSB to specify the

parameter which is to be controlled. Then use Data

Increment/Decrement (page 183) to set the value of the

speciﬁed parameter. Note that once the RPN has been set for

a channel, subsequent data entry will be recognized as the

same RPN’s value change. Therefore after you use the RPN,

you should set a Null (7FH, 7FH) value to avoid unexpected

results.

The following RPN numbers can be received.

■ Channel Mode Messages

The following Channel Mode Messages can be received.

All Sounds Off (Control #120)

Clears all sounds currently sounding on the speciﬁed

channel. However, the status of channel messages such as

Note On and Hold On is maintained.

Reset All Controllers (Control #121)

The values of the following controllers will be reset to the

defaults.

All Notes Off (Control #123)

Clears all notes currently on for the speciﬁed channel.

However, if Hold1 or Sostenuto is on, notes will continue

sounding until these are turned off.

RPN MSB RPN LSB PARAMETER

00 00 Pitch Bend Sensitivity

00 01 Fine Tune

00 02 Coarse Tune

7F 7F Null

2nd BYTE 3rd BYTE MESSAGE

120 0 All Sounds Off

121 0 Reset All Controllers

123 0 All Notes Off

126 0 - 16 Mono

127 0 Poly

CONTROLLER VALUE

Pitch Bend Change 0 (center)

Aftertouch 0 (off)

Polyphonic

Aftertouch 0 (off)

Modulation 0 (off)

Expression 127 (max)

Hold1 0 (off)

Portamento 0 (off)

Sostenuto 0 (off)

Soft Pedal 0 (off)

Portamento Control Cancels the Portamento source key number

RPN Number not speciﬁed; internal data will not change

NRPN Number not speciﬁed; internal data will not change

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF ES7 Seite 183

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info