Bedienungsanleitung Yamaha MOTIF ES7 (Seite 184 von 300) (Englisch)

571272

184

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Basic Structure

About MIDI

184 Owner’s Manual

Mono (Control #126)

Performs the same function as when an All Sounds Off

message is received, and if the 3rd byte (mono number) is in

the range of 0 - 16, it sets the corresponding channel to Mono

Mode (Mode 4: m = 1).

Poly (Control #127)

Performs the same function as when an All Sounds Off

message is received, and sets the corresponding channel to

Poly Mode.

■ Program Change

Messages that determine which voice to select for each Part.

With a combination of Bank Select, you can select not only

basic voice numbers, but also variation voice bank numbers.

For a list of the Voices, see the separate Data List.

■ Pitch Bend

Pitch Bend messages are continuous controller messages

that allow the pitch of designated notes to be raised or

lowered by a speciﬁed amount over a speciﬁed duration.

■ Channel Aftertouch

Messages which let you control the sounds by the pressure

you apply to the keys after the initial striking of the keys, over

the entire channel.

This synthesizer does not transmit this data from the

keyboard; however, this synthesizer does properly respond to

this data when received from an external device.

■ Polyphonic Aftertouch

Messages which let you control the sounds by the pressure

you apply to the keys after the initial striking of the keys, for

each individual key. This synthesizer does not transmit this

data from the keyboard; however, the data is transmitted from

the internal sequencer.

SYSTEM MESSAGES

System messages are the data related to the overall system of

the device.

■ System Exclusive Messages

System Exclusive messages control various functions of this

synthesizer, including master volume and master tuning, tone

generator mode, effect type and various other parameters.

General MIDI (GM) System On (Song mode/Pattern only)

When “General MIDI system on” is received, the MOTIF ES

will receive the MIDI messages which are compatible with GM

System Level 1, and consequently will not receive NRPN and

Bank Select messages.

F0 7E 7F 09 01 F7 (Hexadecimal)

nMake sure that the interval between this message and the ﬁrst note

data of the song is at least a quarter note or greater in length.

Master Volume

When received, the Volume MSB will be effective for the

System Parameter.

F0 7F 7F 04 01 ll mm F7 (Hexadecimal)

* mm (MSB) = appropriate volume value, ll (LSB) = ignored

■ System Realtime Messages

These messages control the sequencer, that is to say Song

and Pattern.

Active Sensing (FEH)

Once FEH (Active Sensing) has been received, if no MIDI

data is subsequently received for longer than an interval of

approximately 300 msec, the MOTIF ES will perform the same

function as when All Sounds Off, All Notes Off, and Reset All

Controllers messages are received, and will then return to a

status in which FEH is not monitored

Timing Clock (F8H)

This message is transmitted with a ﬁxed interval (24 times per

1/4 note) to synchronize connected MIDI instruments.

You can select whether the sequencer block uses the internal

Timing Clock, or external Timing Clock messages received

via MIDI IN by setting the MIDI Sync parameter: [UTILITY] →

[F5] MIDI → [SF3] SYNC → MIDI Sync.

Start (FAH)

This message lets the MIDI sequence data start playing back

from the beginning. This message will be transmitted when

pressing the [F] (Play) button at the top of the Song or

Pattern.

Continue (FBH)

This message lets the MIDI sequence data start playing back

from the current song position. This message will be

transmitted when pressing the [F] (Play) button at the

middle of the Song or Pattern.

Stop (FCH)

This message causes MIDI sequence data (song) to stop

playing back. This message will be transmitted when

pressing the [■] (Stop) button during playback.

nYou can select whether this synthesizer will transmit Timing Clock,

Start, Continue, and Stop messages by setting the SeqCtrl parameter:

[UTILITY] → [F5] MIDI → [SF3] SYNC → SeqCtrl.

■ System Common Message

System Common messages also control the sequencer,

including Song Select and Song Position Pointer messages.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF ES7 Seite 184

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info