Bedienungsanleitung Yamaha MOTIF XS7 (Seite 147 von 320) (Englisch)

586887

147

Zoom out

Zoom in

Vorherige Seite

1/320

Nächste Seite

Editing a Performance

MOTIF XS Owner’s Manual 147

Voice mode

Song mode

Pattern mode

Mixing mode

Master mode

Utility mode

File mode Performance

mode

Sampling

mode 1

Sampling

mode 2

Reference

4Q (Bandwidth)

This varies the signal level at the Frequency setting to

create various frequency curve characteristics. The higher

the setting the smaller the Q (Bandwidth). The lower the

setting, the greater the Q (Bandwidth).

Settings: 0.1 – 12.0

nWhen the Shape parameters (1) of the Low and High are set

to “shelv,” the Q parameters (4) of the Low and High are not

available.

Controller settings—[F3] Ctrl Asgn

(Controller Assign)

You can assign MIDI Control Change Numbers to the

controllers and knobs on the front panel for the selected

Performance. For example, you could use the ASSIGN 1

and 2 knobs to control effect depth, while using the Foot

Controller to control modulation. These control

assignments are called “Controller Assign.” You can have

independent Controller Assign settings for each

Performance.

1Ribbon Controller Control No.

Determines the Controller Change number generated

when you run your ﬁnger across the surface of the Ribbon

Controller.

Settings: 00 – 95

2Foot Controller 1 Control No.

Foot Controller 2 Control No.

Determines the Control Change number generated when

you use the Foot Controller connected to the FOOT

CONTROLLER jack.

Settings: 00 – 95

3Foot Switch Control No.

Determines the Control Change number generated when

you use the Footswitch connected to the FOOT SWITCH

ASSIGNABLE jack.

Settings: 000 – 100

nWhen a Control Change number of 96 or higher is selected,

the function indicated to the right of the number is enabled for

control, but no MIDI Control Change number is actually

assigned to the Footswitch.

4Assign 1 Control No.

Assign 2 Control No.

Determines the Control Change number generated when

you control the ASSIGN1 knob and ASSIGN2 knob with the

TONE1 lamp turned on.

Settings: 00 – 95

5A. Function 1 Control No.

A. Function 2 Control No.

Determines the Control Change numbers generated when

you press the ASSIGNABLE FUNCTION buttons.

Settings: 00 – 95

6Breath Controller Control No.

Determines the Control Change number generated when

you use a Breath Controller connected to the MIDI IN

connector of this instrument.

Settings: 00 – 95

Audio In settings—[F4] Audio In

You can set parameters related to audio input from the A/D

INPUT connector and the mLAN connector.

nThe mLAN Input (m1 – 14) is available only for the MOTIF XS8.

This is available for MOTIF XS6/7 only when an optional

mLAN16E2 has been installed.

1Volume

Determines the output level of the Audio Input Part.

Settings: 0 – 127

2Pan

Determines the stereo pan position of the Audio Input Part.

Settings: L63 (far left) – C (center) – R63 (far right)

3Mono/Stereo

Determines the signal conﬁguration for the Audio Input Part,

or how the signal or signals are routed (stereo or mono).

Settings: L mono, R mono, L+R mono, stereo

L mono

Only the L channel of the audio input is used.

–

Frequency

12.0

0.1

Output Settings—[SF1] Output

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF XS7 Seite 147

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF XS7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info