Bedienungsanleitung Yamaha MOTIF8 (Seite 265 von 300) (Englisch)

571289

265

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

265

MOTIF Reference

File mode

Reference File mode

● [F1]-[SF2] CONFIG SCSI ID

From this display you can specify the ID number for

all the devices in the SCSI chain, including the host

(the MOTIF itself).

• SELF

Determines the ID number (0 - 7) for the MOTIF, as the

SCSI host. If you change this setting, you’ll need to turn

the power off and on again for the new setting to take

effect.

• SCAN

This control lets you mount each device in the SCSI chain,

making sure that the MOTIF properly recognizes it. Move

the cursor to the appropriate SCAN circle in the display,

and press the [INC/YES] button to mark the circle and

mount the corresponding device.

● [F1]-[SF3] CONFIG Mount

From this display you can select speciﬁc partitions

for saving/loading data, within the device mounted

in the SCSI ID display (above).

● [F1]-[SF4] CONFIG Format

Before you can use a new Memory Card/SCSI

device with the MOTIF, you will need to format it.

Use this operation to format the memory card or

SCSI device and assign a Volume Label to it.

• Type

Determines the type of the device to be formatted.

❏ Settings See below.

car

When this is set, the Memory card inserted to the Card slot

is formatted.

all (SCSI)

When this is set, all the SCSI devices connected to the

MOTIF are formatted.

partition 1 ~ 4 (SCSI)

When this is set, one partition (speciﬁed at the bottom of

the display) of the SCSI device connected to the MOTIF is

formatted.

• Format

This parameter is available when the Type is set to “all

(SCSI).” A hard disk (or any similar storage media) must

be physically formatted before it can be logically

formatted. Physical formatting (also called “low-level”

formatting) arranges the disk into physical elements such

as tracks and sectors.

Physical formatting is usually done by the manufacturer;

you may not need to do it yourself. Logical formatting

places a ﬁle system on the disk, allowing the MOTIF to

access the disk.

You’ll need to logically format any media you use before

you can use it with the MOTIF.

❏ Settings physical, logical

• Volume Label

Names the Volume Label. Refer to “Basic Operation” for

instructions on naming on page 73.

n Make sure to enter the Volume Label. An error

message appears if you press the [ENTER] button

without entering the Volume Label.

1 After setting the relevant parameters above, press

the [ENTER] button. (The display prompts you

for conﬁrmation.)

2 After formatting has been completed, a

“Completed” message appears and operation

returns to the original display.

n To cancel the Format operation, press the

[DEC/NO] button.

While formatting is in progress, never eject the Memory

card or turn off the power to the MOTIF.

If data is already saved on the memory card/SCSI device,

be careful not to format it. If you format the memory card/

SCSI device, all the previously recorded data will be

deleted.

The SCSI devices connected to and in use by

the MOTIF are shown at the corresponding ID

numbers, set on the devices themselves.

Volume label of the selected partition

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF8 Seite 265

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info