Bedienungsanleitung Yamaha MOX6 (Seite 36 von 76) (Englisch)

571302

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

MOX6/MOX8 Owner’s Manual

Quick Guide

Connecting a microphone

or audio equipment

Playing the keyboard along with

the sound input from the A/D

INPUT [L]/[R] jacks

You can have the A/D input sound—such as your voice

through a microphone, a guitar, bass, or CD player—assigned

as an Audio Input Part. Various parameters such as volume,

pan, and effect can be set to this Part and the sound is output

together with the sound of your keyboard performance. In

these example instructions, you’ll learn how to use the A/D

input sound in the Voice mode.

1 Make sure to turn off the power of this instrument

and set the A/D INPUT [GAIN] knob to the minimum.

2 Connect the audio equipment or the microphone

to the A/D INPUT [L]/[R] jack on the rear panel.

NOTE A standard dynamic microphone is recommended. (This

instrument does not support phantom-powered condenser

microphones.)

3 Turn on the connected audio equipment, then turn

on the MOX6/MOX8.

4 Press the [VOICE] button to enter the Voice Play

mode.

5 Press [UTILITY]  [F3] VCE A/D  [SF1] OUTPUT,

then set the “Mono/Stereo” parameter.

This parameter determines the signal configuration for the

audio signal via the A/D INPUT [L]/[R] jacks, or how the signal

or signals are routed (stereo or mono).

When connecting the audio device as shown in step 2, set

this parameter to “stereo” or “LRMono.” When connecting

the microphone as shown in step 2, set this parameter to

“LMono.”

If necessary, set the other parameters.

NOTE For details about the parameters including Mono/Stereo,

see the “Reference Manual” PDF document.

NOTE The above parameter settings including Mono/Stereo are

applied to the entire Voice mode. If necessary, press the

[STORE] button to store these with the Utility settings.

NOTE The above parameter settings including Mono/Stereo differ

depending on the selected mode.

NOTE

For the Performance mode, set the above parameters on the

display called up via [PERFORM]

 [EDIT]  [COMMON]

 [F5] A/D IN  [SF1] OUTPUT. The settings will be stored

for each Performance.

For the Song/Pattern mode, set this parameter on the display

called up via [SONG] or [PATTERN]

 [MIXING]  [EDIT]



[COMMON]



[F5] A/D IN



[SF1] OUTPUT. The settings

will be stored for each Song/Pattern.

6 Press [UTILITY]  [F1] GENERAL  [SF6] OTHER,

then set the “Mic/Line” parameter according to

the equipment connected to the A/D INPUT [L]/[R]

jacks.

When connecting equipment of low output level (such as a

microphone, guitar, bass), set this parameter to “mic.” When

connecting equipment of high output level (such as a

synthesizer keyboard, CD player), set this parameter to “line.”

NOTE This setting is available for all modes. If necessary, press

the [STORE] button to store this with the Utility settings.

7 Press the A/D INPUT [ON/OFF] button so that its

lamp lights.

This setting enables audio signals to be input from the

connected audio device.

MOX6/MOX8

Stereo audio equipment (CD player, etc.)

A/D INPUT

[R]

A/D INPUT

[L]

MOX6/MOX8

Microphone

A/D INPUT

[L]/[R]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOX6 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOX6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info